Hello Guest it is May 20, 2019, 11:38:25 PM

Author Topic: New people welcome !! Come in here and introduce your self!  (Read 3339637 times)

0 Members and 2 Guests are viewing this topic.

Re: New people welcome !! Come in here and introduce your self!
« Reply #1070 on: March 10, 2011, 06:49:57 PM »
Please post any questions you have in their own topic,  either the General forum (probably best) or one of the specific forums.
This thread doesnt get too many people looking at it and also it is preferred if it is just kept as an introduction thread rather than a Q&A thread.
Hood
[
 sorry I should have asked can you Jog it back.it will not move of its own accord
  Dick
Re: New people welcome !! Come in here and introduce your self!
« Reply #1071 on: March 11, 2011, 09:52:41 AM »
1st post. Just lurking really as I just have a passing interest in CNC. Looks a great forum though.
Regards,
Dennis
Re: New people welcome !! Come in here and introduce your self!
« Reply #1072 on: March 11, 2011, 12:14:55 PM »
Hi everyone
Live in the Northeast part of the US
I like mechanical stuff so I bought a Mach Motion kit for my Series 2 cnc
Having fun hooking it up after work.
Looking for advice so I came here.

Thank you for your time and consideration
Northeast :)
Re: New people welcome !! Come in here and introduce your self!
« Reply #1073 on: March 12, 2011, 09:07:36 PM »
Hello everyone my name is Ed and I am new to the CNC.  I am from Wisconsin
Re: New people welcome !! Come in here and introduce your self!
« Reply #1074 on: March 13, 2011, 05:23:02 AM »
      ;D Welcome aboard Northeast  & Ed nice to have you with us

      Dick   ;)
Re: New people welcome !! Come in here and introduce your self!
« Reply #1075 on: March 13, 2011, 08:05:56 PM »
Hi, I`m lil coupe and just got my EZ Router  4x4 APC going after having it for about 6 months, still having a problem with the torch not coming on after intering the G code and hitting start. the person that helped me says the M code which is sappose to control the torch isn`t getting  signal from the THC (torch head controller) to the plasma tool. any ideas? thought I`d check the cord first.
Re: New people welcome !! Come in here and introduce your self!
« Reply #1076 on: March 13, 2011, 08:18:43 PM »
 ;D   Welcome aboard Lil coupe
  This only a introduction thread ,you will need to contact the main forum I'm sure that they can be of help

    Dick  ;)

Offline Fredzway

*
  •  8 8
  • I don't suffer from insanity, I enjoy every minute
    • View Profile
Re: New people welcome !! Come in here and introduce your self!
« Reply #1077 on: March 14, 2011, 08:52:13 PM »
"new" to this, I have been around machining since I was a pup. Dad owned a machine shop with a power shaft down each side of the building. Did a lot of precision grinding on ceramics a few years ago. Had Autocad in college at the tender age of 40. Didn't use it much in the ceramics job. I bought a Zen toolworks 7X7 mill. Clamped a Dremel in it and thanks to Mach3 and this forum I am making chips. I make wooden Christmas tree ornaments for family and friends. I started with what are called tablesaw snowflakes and I have "progressed?" to the point of needing digital help. I hope to utilize Lazy CAM and Mach3 to progress on into total madness, I am hooked already!!  Fred
I am an old man and have known a great many troubles, most of them never happened. - Mark Twain
Re: New people welcome !! Come in here and introduce your self!
« Reply #1078 on: March 15, 2011, 12:06:21 AM »
    ;D  Welcome aboard Fredzway
      Yes It is addictive  ::)

         Dick

Offline Tweakie.CNC

*
  • *
  •  7,764 7,764
  • Super Kitty
    • View Profile
    • Tweakie.CNC
Re: New people welcome !! Come in here and introduce your self!
« Reply #1079 on: March 15, 2011, 05:50:15 AM »
Hi Trickey,

I never got a 'welcome aboard' when I joined the forum and I am feeling a bit left out here  :'( :'(

Tweakie.
Success consists of going from failure to failure without loss of enthusiasm.  Winston Churchill.