Messages

1701

NC Pod / Re: Welcome To The NC Pod Development, Discussion and Support Topic

« on: January 17, 2007, 05:02:21 PM »

Wayne,
I have no idea how you have the time to do all the stuff that you do! It would be so fun to retro the Mill that you did and it looks like you are having a good time with the lathe too... and Here I am Stuck to the KB ;(

Someday!

1702

NC Pod / Re: Missing steps in jog follow mode

« on: January 17, 2007, 04:40:12 PM »

At this point I will not do any more testing till there is updated firmware and software... I have the results from the scope and I can tell you that after they get this last little bit fixed we are as good as gold There is very little phase jitter in the pulse stream when it is working right...

1703

General Mach Discussion / Re: Cabin Fever

« on: January 17, 2007, 04:31:30 PM »

I will also Have some MPG's with me and a machine you can test them on I will be selling them for 75.00 each

Very cool toy!

BTW Ron I expect to see you for beer Firday night (At the hotel) and I am going to buy! 

1704

General Mach Discussion / Re: x axis mounted and working, y & z stalling!

« on: January 17, 2007, 04:29:52 PM »

You should be running Mach3... I hate mach2

All that said I don't get why you need to run in rutex mode... I think we should get your ports and pins setup for Mach3. Are you good with that?

1705

General Mach Discussion / Re: Setup estop, spindle on/off, and Xylotex 3 axis drive

« on: January 17, 2007, 04:27:11 PM »

I had a look at there page and I can't see that there is a relay on there board... could you post what one you have and if you could the pin out for it ?

thanks
Brian

1706

General Mach Discussion / Re: New PlugIn

« on: January 17, 2007, 01:43:57 AM »

That is cake   I could do that in about 10 min (after all I have most of it done)

1707

LazyCam (Beta) / Re: Thanks to Brian & or Lazy cam Team! Please keep up the good work!!!

« on: January 16, 2007, 07:15:48 PM »

Hello Jerald,
I would like to thank you for the nice words! I can tell you that from time to time it gets hard to hear I need this, this isn't working right, You NEED to add this, I can't get it to work, and yes at times I need something better... To all that I say OKAY and keep a smile on my face! I love what I do and would never give it up...  Art is having a good time but I think he needs to go cook in the sun for a week

So thank you again and please know that when you buy a license file you are not buying software as much as you are joining a group of great people that help each other! I can't tell you how proud Art and I are of all you users that help all the there uses and help us make the software better

So thank you!!!

Brian
 

1708

General Mach Discussion / Re: Help with scale

« on: January 16, 2007, 06:48:02 PM »

OR you could use the "Calc Steps Per Unit" onthe settings page it should get you started...

1709

General Mach Discussion / Re: Arrow Key Controls

« on: January 16, 2007, 06:46:45 PM »

I did the same thing one time... You would think I would know better!

 

1710

General Mach Discussion / New PlugIn

« on: January 16, 2007, 10:28:14 AM »

Hello,
I wanted to tell you that I made you all a gift in my free time
This Pluging is Called JCode (Jog to Gcode) I have no idea what you will use it for but it is a fun toy and could be used to make your machine do great things like dip a tea bag and stir in the honey all by jogging!

Or you could use it to teach facing a part because Cam is just to slow... that works for me too (I would rather have a good cup of tea) 

You can get it here on the Plugin's page:
http://www.machsupport.com/artsoft/plugin.htm

Thanks
Brian