Messages

1761

Show"N"Tell ( Your Machines) / Re: Eagle KM-750..Anilam Crusader GX-M

« on: January 07, 2007, 07:21:35 PM »

I was just running my eagle from an NC pod and you are going to need more KHz then that can give I could only get to just over 130 IPM and had to reduce the PPU to 10,000 to get 427 IPM I was running at 25000PPU and 500 IMP with the G100. This machine gets more hardware then most.. it is the test bed that I run all the hardware on

I have 50,000 steps per inch when I done have a step multiplier set in the drives.. that is the best I can do on the mill that I test with

Just wanted to tell you that there is a 75KHz limit on the NCPod... If you get a Galil it is only limited to the encoders and I think it is about 13MHz that it will read them at. It is a Nice fast way to go if you have the hardware that needs it. You could run your old drives with a galil too...

Better then that is the Delta Tau stuff that we will soon be programing for... I think they will take in up to 40 MHz on the encoders and output at 4MHz if you would like to run step and direction... The PC104 will also run in velocity mode and torque mode as well.

Well that is about all I can tell you about the things we are working on getting running... as you can see there is going to be GREAT speed in the future with true closed loop! IT just takes time for us to get the work done

1762

VB and the development of wizards / Re: Internal variables

« on: January 07, 2007, 11:24:05 AM »

I would have a look at the code in the Calc steps per unit button on the settings page. I used some of that stuff in there...

1763

General Mach Discussion / Re: MANURHIN LATHE AUTOMATICE

« on: January 07, 2007, 11:21:33 AM »

Is the late running stepper motors? If it is you could take all the old stuff off and put on new Drives I think this is about all you can do with this.. I don't know that machine at all.

1764

Mach SDK plugin questions and answers. / Re: Shuttle Xpress Problem

« on: January 06, 2007, 06:38:08 PM »

If you installed the software for the shuttle you will need to take it out You need NO software!

1765

LazyCam (Beta) / Re: New LazyCam has lots of problems

« on: January 06, 2007, 06:35:49 PM »

That is odd...  I will look and see how you could get that problem.

What are you running for computers?

1766

General Mach Discussion / Re: hexapod

« on: January 06, 2007, 06:33:23 PM »

Well if we get a free day we will look into it

1767

General Mach Discussion / Re: Set Z to zero automatically?Auto tool zero questions

« on: January 06, 2007, 06:28:10 PM »

All The guys are doing is ::)using a chunk of AL .125 plate and when the tool hits the part it tells the computer that it is there... I didn't think something like this would work but I was wrong   

You would hook the frame to one side and the plate to the other side of the input... I have no idea how they stop noise from being a problem.
Hope that helps
Brian

1768

General Mach Discussion / Re: Screw mapping

« on: January 06, 2007, 06:24:19 PM »

I have not used that function   It was something that was added a long time ago for only a few users... There should be a section in the manual on it

1769

General Mach Discussion / Re: MANURHIN LATHE AUTOMATICE

« on: January 06, 2007, 06:22:50 PM »

Is there a link where we can see the specs of the machine that you ere talking about?

1770

Galil / Re: Mach3 + Galil

« on: January 06, 2007, 09:22:14 AM »

Send me a PM off list with your phone number and I will send you back a new plugin that should fix that problem... I will also tell you how to set the setting that I am about to add