Messages

481

Mach3 under Vista / Re: Will MACH3 ever support 64-bit systems? Officially? FYI, it's 2010

« on: January 12, 2010, 09:42:42 AM »

Well the driver is 32bit and we are thinking about making a 64Bit driver ... We thought he P Port would have been gone by now LOL...

Talked to Art and he is going to setup a 64 bit system to test with..

Thanks
Brian

482

General Mach Discussion / Re: Mach3 Rev4

« on: January 10, 2010, 03:21:21 PM »

The screen will be a 4 axis screen.. but you will be able to change it into a 5 axis screen if you like

483

General Mach Discussion / Re: Mach3 Rev4

« on: January 10, 2010, 10:52:23 AM »

Lathe is about to get the update it has needed for some time.. This update should also spill over a bit into mill   We will see how it goes!

Thanks
Brian

484

General Mach Discussion / Re: Mach3 Rev4

« on: January 10, 2010, 10:37:17 AM »

Hello guys,
We are working on finishing up mill in legacy mode now and as soon as that is finished I was going to get Turn up and working in Legacy mode.  When all that is done we will be able to make and use a new Lathe screen using the new VB and system vars.

The code for Rev 3 and rev 4 are not the same at all so it is like I am working on two diffrent programs . So doing bug fixes and working on rev 4 has been very taxing on me but I feel it is going to be well worth it when it is done!


Thanks
Brian

485

General Mach Discussion / Re: I truely believe it's a bug with many versions:

« on: December 24, 2009, 10:18:28 AM »

I would like to have your XML to test. You can upload it here in a zip file

486

General Mach Discussion / Re: COMPLEX THREADING WIZARD

« on: December 22, 2009, 09:41:36 PM »

I was in hopes that the complex wizard would go away it was far to complex  to be useful ;(

But if you would like to fix it... You have my permission to do anything you like

487

General Mach Discussion / Re: I truely believe it's a bug with many versions:

« on: December 22, 2009, 09:33:10 PM »

I see that you are getting the error in a jog... that may be a problem with phase jitter.

Also I see you say you are getting an over volocity.. Could you please tell me if you get the error in Exact stop? I know where there is a problem with CV and I have added some code to check for this but there are times the CV will enter the move a bit to fast..

Thanks
Brian

488

General Mach Discussion / New Plugin Interface for Rev4

« on: October 21, 2009, 11:19:55 AM »

Hello,
I have done a first draft of the new plugin interface for the Mach3 Rev4. This interface changes some of the var names (Less then 5%) and a few other minor changes. This Doc I hope will show the amount of work that is needed to convert a plugin from Rev 3 to Rev 4 . This should allow for any version of C++ to be used when I am finished but I need to make some new methods for getting and setting Strirngs. The reason for this is that CStrings are not part of the C++ STL   More on that later as I finish it up.

Please tell me if you have a hard time following the guide.

Thanks
Brian

BTW this is only for the plugin authors

489

General Mach Discussion / Re: re: Whats happened to Mach.4 update

« on: October 20, 2009, 07:53:12 AM »

You are all set They do a good job!

490

General Mach Discussion / Re: re: Whats happened to Mach.4 update

« on: October 19, 2009, 09:46:21 PM »

Mach3 Rev4.0.1 is going to be a devlopment version.. when it is ready fo rthe light of day ..