Hello Guest it is April 19, 2024, 09:16:29 AM
Profile Guest
« previous next »
Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 »   Go Down

Author Topic: Problems threading on the lathe  (Read 434279 times)

0 Members and 1 Guest are viewing this topic.

Offline panaceabeachbum

*
  • 338 338
    • View Profile
Re: Problems threading on the lathe
« Reply #20 on: September 26, 2008, 10:48:13 PM »
smooth stepper landed today , the first one had male db25 and plugged right into my c11 BOB , This one came with female db25 on the cables, will have to figure something out in the morning to plug it into the c11 BOB on the lathe.

Brett and Hood stay tuned, many stupid questions to follow
Logged

Offline Overloaded

*
  • *
  • 4,921 4,921
    • View Profile
Re: Problems threading on the lathe
« Reply #21 on: September 29, 2008, 11:27:56 PM »
Hey RT,
Would you mind to check this for me ?
http://www.machsupport.com/forum/index.php?topic=8461.new#new
If this is the screen that you are using.
Thanks,
RC
Logged

Offline Rieks

*
  • 26 26
    • View Profile
Problems threading on the lathe
« Reply #22 on: February 22, 2009, 04:23:11 PM »
Hello all,

While treading on the lathe, the x-axis is walking slow in or out on some cuts :o ???.
Can some one tel me what the solution is?

Rieks
Logged

Offline Hood

*
  • 25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: Problems threading on the lathe
« Reply #23 on: February 22, 2009, 04:53:57 PM »
What is the code you are using?
Hood
Logged

Offline RICH

*
  • *
  • 7,427 7,427
    • View Profile
Re: Problems threading on the lathe
« Reply #24 on: February 22, 2009, 07:22:50 PM »
What version of MACH are you using?

How are you generating the threading code? Wizard, M76, G32?

What is the condition of your lathe?
- Ball screws / steppers / backlash ?

What are you using for an index?

RICH
Logged

Offline Rieks

*
  • 26 26
    • View Profile
Re: Problems threading on the lathe
« Reply #25 on: February 23, 2009, 08:29:38 AM »
Hello,

The version I use is R3.042.020 and I use the wizard "Threading" in Lathe, thus G76
Logged

Offline Hood

*
  • 25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: Problems threading on the lathe
« Reply #26 on: February 23, 2009, 08:32:50 AM »
and what is the code that gives you the problem?
Hood
Logged

Offline Rieks

*
  • 26 26
    • View Profile
Re: Problems threading on the lathe
« Reply #27 on: February 23, 2009, 10:30:23 AM »
When treading, after 2 or 3 cuts, wit  a depth of 0.2 mm, befor the next Z-axis movement in negativ
direction, the X-axis feeds in 0.2 mm, and then, when Z-axis moves in, the X-axis moves slowly out, as if
a taper is cut.

Rieks
Logged

Offline Hood

*
  • 25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: Problems threading on the lathe
« Reply #28 on: February 23, 2009, 10:47:03 AM »
please give an example of the problem code.
Hood
Logged

Offline Rieks

*
  • 26 26
    • View Profile
Re: Problems threading on the lathe
« Reply #29 on: February 25, 2009, 03:28:13 PM »
Hello Hood,

sorry for the delay, Here is the problem code.
It is the first time I tested the threading wizard.

Rieks
Logged
Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 »   Go Up
« previous next »