Hello
Guest
it is
April 23, 2024, 04:58:48 PM
Guest
Login
Register
Menu
Home
Help
Search
Calendar
Members
Members
View the memberlist
Search For Members
Login
Register
YouTube
Machsupport Forum
/
Mach Discussion
/
General Mach Discussion
/
Newbie to cnc building in need of some help please
« previous
next »
Print
Pages:
«
1
2
3
4
5
6
7
»
Go Down
Author
Topic: Newbie to cnc building in need of some help please (Read 7493 times)
0 Members and 1 Guest are viewing this topic.
TPS
2,505
Re: Newbie to cnc building in need of some help please
«
Reply #30 on:
January 20, 2019, 10:34:25 AM »
just to confirm:
-Settings -> Port's&Pin's -> Port Setup and axis selection -> Port 1 is enabled
-Settings -> Port's&Pin's -> Port Setup and axis selection -> Port 1 adress is set correctly
-Settings -> Port's&Pin's -> Motor Outputs -> axis is enabled
-Settings -> Port's&Pin's -> Motor Outputs -> Step Pin , Dir Pin and port are correct
Logged
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.
scooternauman
41
Re: Newbie to cnc building in need of some help please
«
Reply #31 on:
January 20, 2019, 10:43:59 AM »
port 1 is enabled. port address is in question. axis is enabled. I'm pretty sure i have pins and ports correct. x=2,3 y=4,5 z=6,7
if i go into my control panel I'm not sure what I'm looking for.
Logged
scooternauman
41
Re: Newbie to cnc building in need of some help please
«
Reply #32 on:
January 20, 2019, 10:46:06 AM »
when i click on devices in my control panel all it shows is a microsoft xps document writer and I'm not sure why that is
Logged
TPS
2,505
Re: Newbie to cnc building in need of some help please
«
Reply #33 on:
January 20, 2019, 10:50:24 AM »
sorry have only a german version
Logged
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.
scooternauman
41
Re: Newbie to cnc building in need of some help please
«
Reply #34 on:
January 20, 2019, 10:57:43 AM »
lol I wish I knew what that said. However the only devices shown connected in my control panel are wifi adapter , keyboard,moniter, pc and mouse.
I deleted the document writer because there is none.
Logged
TPS
2,505
Re: Newbie to cnc building in need of some help please
«
Reply #35 on:
January 20, 2019, 11:02:24 AM »
but you said, you run drivertest succesfuly?
Logged
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.
scooternauman
41
Re: Newbie to cnc building in need of some help please
«
Reply #36 on:
January 20, 2019, 11:03:15 AM »
that is correct
Logged
scooternauman
41
Re: Newbie to cnc building in need of some help please
«
Reply #37 on:
January 20, 2019, 11:04:16 AM »
just ran it again and it says system excellent
Logged
TPS
2,505
Re: Newbie to cnc building in need of some help please
«
Reply #38 on:
January 20, 2019, 11:06:10 AM »
can't run drivertest here (64Bit), is there any port adresss shown?
Logged
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.
scooternauman
41
Re: Newbie to cnc building in need of some help please
«
Reply #39 on:
January 20, 2019, 11:07:40 AM »
no port shown
Logged
Print
Pages:
«
1
2
3
4
5
6
7
»
Go Up
« previous
next »