Hello Guest it is December 13, 2019, 04:55:33 AM

Author Topic: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A  (Read 43359 times)

0 Members and 1 Guest are viewing this topic.

Online TPS

*
  •  1,411 1,411
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #80 on: June 08, 2015, 02:07:12 PM »
thank's a lot Thomas !
It's no problem with the manual language = "Ich spreche auch Deutsch - Zwei Jahre in Deutschland gelebt, im Koblenz"

ok das ist gut.

Thomas
anything is possible, just try it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline slvm

*
  •  68 68
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #81 on: June 16, 2015, 05:12:14 AM »
Hi All
Got good news and also some questions :
1-I run one test on cnc (after set the spindle only for CW rotation) it seems to be good (with one mill for hand machine and curved material, without vacuum hold )
2-I don't know why on Y the cnc made mirror (it is perhaps because I revrse Y Axis on home limit set-up) ? I revrse the Y because by Manual-Jog.
Unfortunate here can not post the short movie.

Online TPS

*
  •  1,411 1,411
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #82 on: June 16, 2015, 07:06:43 AM »
Hi Emil,

looks quite good so far.

--2-I don't know why on Y the cnc made mirror (it is perhaps because I revrse Y Axis on home limit set-up) ? I revrse the Y because by Manual-Jog.

X and Y have to be set like a normal coordinate system, so if we say in a rectangle
X0Y0 is the left bottom corner

X+ is going to the right side
Y+ is going upwards

allways relayed to the material.

for your spindle CCW turn.
have you tryed this pin 4   (REV)  reverse rotation -> csmio digtal output to switch CW/CCW
on the inverter for reverse run ?

Thomas





anything is possible, just try it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline slvm

*
  •  68 68
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #83 on: June 16, 2015, 11:05:14 AM »
Regarding "spindle reverse pin 4"
I try but it seems don't work, I think the inverter is in some how pre-programmed .
Another spindle problem is the brake, when goes stop (end of part-programm the HSD motor-spindle do some strange noise and brake abrupt)
how can I can set some delay in brake ?
any way I think I solve the main problem and now is VB for ATM and drill unit.... :( + FINE TUNNING

PS give me on PM your mail to send you the movies.
I wonder what happen with Hood , ...!? How are you Hood ?
« Last Edit: June 16, 2015, 11:11:06 AM by slvm »

Online TPS

*
  •  1,411 1,411
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #84 on: June 17, 2015, 09:23:03 AM »
Hi Emil,

is there any posibility on this Inverter to Change Parameters,
in the Manual it does not look like there is any Display.

my email is below  the avantar.

Thomas
anything is possible, just try it.
if you find some mistakes, in my bad bavarian english,they are yours.

Online TPS

*
  •  1,411 1,411
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #85 on: June 17, 2015, 09:27:26 AM »
by the way,

is the spindle changing direction if you swap the analog Input wires ?
anything is possible, just try it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline slvm

*
  •  68 68
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #86 on: June 17, 2015, 10:19:47 AM »
by the way,

is the spindle changing direction if you swap the analog Input wires ?
When I change the reff wires the spindle change direction.
Can you help me with the tool change VB ?

Online TPS

*
  •  1,411 1,411
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #87 on: June 17, 2015, 11:23:33 AM »
Hi Emil,
When I change the reff wires the spindle change direction.
Can you help me with the tool change VB ?

that means you can use a gold contact relay to swap the wires to change direction.
wire this relay to a csmio output and we do some changes in M3/M4 to get this
working.

just let me know what help you need for the toolchange macro.

Thomas
anything is possible, just try it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline slvm

*
  •  68 68
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #88 on: June 17, 2015, 12:02:23 PM »
Thomas

I use already 2 relays to change the direction but some people said is not OK to use by M4 - to +; but if you say is OK then I will do it.

By VB ATC I'm almost = 0.....First I will wire the C axis-encoder for the ATC and check the drive and the motor.

Online TPS

*
  •  1,411 1,411
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #89 on: June 17, 2015, 04:35:46 PM »
Hi Emil;
Thomas

I use already 2 relays to change the direction but some people said is not OK to use by M4 - to +; but if you say is OK then I will do it.


maybe i missed something about this two relaiys,
pls give me a short update about this two relais.

Thomas
anything is possible, just try it.
if you find some mistakes, in my bad bavarian english,they are yours.