Hello Guest it is June 25, 2026, 05:33:55 AM
Profile Guest
« previous next »
Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 »   Go Down

Author Topic: Mach3, Opt Laser 5W and Aspire  (Read 122803 times)

0 Members and 7 Guests are viewing this topic.

Offline A11an

*
  • 62 62
Re: Mach3, Opt Laser 5W and Aspire
« Reply #90 on: February 24, 2021, 12:47:07 PM »
Ok, I'll see what I can do to build a board and come back,

thanks for you time and effort, much appreciated

Allan

Logged

Offline A11an

*
  • 62 62
Re: Mach3, Opt Laser 5W and Aspire
« Reply #91 on: February 24, 2021, 12:56:04 PM »
Just checking, It says something about Diode lasers using Active High TTL input, is mine?

does it show a different board for that, sorry out of my depth here!
Logged

Offline TPS

*
  • 2,627 2,627
Re: Mach3, Opt Laser 5W and Aspire
« Reply #92 on: February 24, 2021, 01:15:57 PM »
you are right, sorry to Point you to the wrong circuit.
Logged
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline A11an

*
  • 62 62
Re: Mach3, Opt Laser 5W and Aspire
« Reply #93 on: February 24, 2021, 01:24:24 PM »
Quote from: TPS on February 24, 2021, 01:15:57 PM
you are right, sorry to Point you to the wrong circuit.

Just to be sure it's the active high one I need to make?
Logged

Offline A11an

*
  • 62 62
Re: Mach3, Opt Laser 5W and Aspire
« Reply #94 on: February 24, 2021, 05:05:42 PM »
To be honest I don't understand the schematics drawing or understand how to read the truth table, any help would be really appreciated.
Logged

Offline TPS

*
  • 2,627 2,627
Re: Mach3, Opt Laser 5W and Aspire
« Reply #95 on: February 24, 2021, 11:28:11 PM »
you have to choose TTL(H) variant.
Logged
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline A11an

*
  • 62 62
Re: Mach3, Opt Laser 5W and Aspire
« Reply #96 on: February 25, 2021, 12:20:47 AM »
I just don't understand the drawing schematic of the board
Logged

Offline A11an

*
  • 62 62
Re: Mach3, Opt Laser 5W and Aspire
« Reply #97 on: February 25, 2021, 02:18:55 AM »
is there any reason the drawing can't be like the attached so an idiot like me can understand?   :)
Logged

Offline Tweakie.CNC

*
  • *
  • 9,359 9,359
  • Super Kitty
Re: Mach3, Opt Laser 5W and Aspire
« Reply #98 on: February 25, 2021, 05:09:21 AM »
Hi Allan,

I am sure you are not an idiot but if you need to make one of these boards I can provide you with a circuit diagram although I should perhaps read through your laser manual to determine if such a board is really necessary or not.

I have been using a UC400ETH controller for over a year now but not with Mach3.
Stupid question but have you established that the Mach3 plugin for the UC400ETH does in fact support the M11Px / M10Px command set ?

Tweakie.
Logged
PEACE

Offline A11an

*
  • 62 62
Re: Mach3, Opt Laser 5W and Aspire
« Reply #99 on: February 25, 2021, 06:05:09 AM »
What do I need to do to find out?

Allan
Logged
Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 »   Go Up
« previous next »