Hello Guest it is December 03, 2021, 09:39:20 PM

Author Topic: Mach3, Opt Laser 5W and Aspire  (Read 3214 times)

0 Members and 1 Guest are viewing this topic.

Offline TPS

*
  •  2,210 2,210
    • View Profile
Re: Mach3, Opt Laser 5W and Aspire
« Reply #80 on: February 24, 2021, 01:24:51 PM »
can pin 14 be used where my spindle is usually connected?
Yes.
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline A11an

*
  •  62 62
    • View Profile
Re: Mach3, Opt Laser 5W and Aspire
« Reply #81 on: February 24, 2021, 01:26:48 PM »
Do you mean yes but still have to build Tweakies board?

Offline TPS

*
  •  2,210 2,210
    • View Profile
Re: Mach3, Opt Laser 5W and Aspire
« Reply #82 on: February 24, 2021, 01:28:07 PM »
can pin 14 be used where my spindle is usually connected?
Yes.

but then you have to use two profiles or Change pin assignment in Config -> Port's and Pin's ->Motor Outputs ->
Spindle.
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline A11an

*
  •  62 62
    • View Profile
Re: Mach3, Opt Laser 5W and Aspire
« Reply #83 on: February 24, 2021, 01:28:54 PM »
I am using 2 profiles

Offline A11an

*
  •  62 62
    • View Profile
Re: Mach3, Opt Laser 5W and Aspire
« Reply #84 on: February 24, 2021, 01:29:40 PM »
For now I don't mind disconnecting the spindle and connecting laser, then maybe build a board

Offline TPS

*
  •  2,210 2,210
    • View Profile
Re: Mach3, Opt Laser 5W and Aspire
« Reply #85 on: February 24, 2021, 01:29:52 PM »
Do you mean yes but still have to build Tweakies board?

you have to build tweakies board, because your BOB creates 0-10V and no PWM as far i can see.
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline A11an

*
  •  62 62
    • View Profile
Re: Mach3, Opt Laser 5W and Aspire
« Reply #86 on: February 24, 2021, 01:31:34 PM »
I control the spindle speed through mach3?

Offline TPS

*
  •  2,210 2,210
    • View Profile
Re: Mach3, Opt Laser 5W and Aspire
« Reply #87 on: February 24, 2021, 01:37:10 PM »
I control the spindle speed through mach3?
yes, but you control it by using the 0-10V Signal, or am i wrong?
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline A11an

*
  •  62 62
    • View Profile
Re: Mach3, Opt Laser 5W and Aspire
« Reply #88 on: February 24, 2021, 01:39:20 PM »
Oh yes, sorry

Offline TPS

*
  •  2,210 2,210
    • View Profile
Re: Mach3, Opt Laser 5W and Aspire
« Reply #89 on: February 24, 2021, 01:39:33 PM »
the plan is to use the PWM Input of your Laser control
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.