Hello Guest it is May 02, 2025, 03:05:52 PM
Profile Guest
« previous next »
Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 »   Go Down

Author Topic: Mach3, Opt Laser 5W and Aspire  (Read 53653 times)

0 Members and 3 Guests are viewing this topic.

Offline TPS

*
  • 2,574 2,574
Re: Mach3, Opt Laser 5W and Aspire
« Reply #80 on: February 24, 2021, 01:24:51 PM »
Quote from: A11an on February 24, 2021, 01:19:52 PM
can pin 14 be used where my spindle is usually connected?
Yes.
Logged
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline A11an

*
  • 62 62
Re: Mach3, Opt Laser 5W and Aspire
« Reply #81 on: February 24, 2021, 01:26:48 PM »
Do you mean yes but still have to build Tweakies board?
Logged

Offline TPS

*
  • 2,574 2,574
Re: Mach3, Opt Laser 5W and Aspire
« Reply #82 on: February 24, 2021, 01:28:07 PM »
Quote from: TPS on February 24, 2021, 01:24:51 PM
Quote from: A11an on February 24, 2021, 01:19:52 PM
can pin 14 be used where my spindle is usually connected?
Yes.

but then you have to use two profiles or Change pin assignment in Config -> Port's and Pin's ->Motor Outputs ->
Spindle.
Logged
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline A11an

*
  • 62 62
Re: Mach3, Opt Laser 5W and Aspire
« Reply #83 on: February 24, 2021, 01:28:54 PM »
I am using 2 profiles
Logged

Offline A11an

*
  • 62 62
Re: Mach3, Opt Laser 5W and Aspire
« Reply #84 on: February 24, 2021, 01:29:40 PM »
For now I don't mind disconnecting the spindle and connecting laser, then maybe build a board
Logged

Offline TPS

*
  • 2,574 2,574
Re: Mach3, Opt Laser 5W and Aspire
« Reply #85 on: February 24, 2021, 01:29:52 PM »
Quote from: A11an on February 24, 2021, 01:26:48 PM
Do you mean yes but still have to build Tweakies board?

you have to build tweakies board, because your BOB creates 0-10V and no PWM as far i can see.
Logged
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline A11an

*
  • 62 62
Re: Mach3, Opt Laser 5W and Aspire
« Reply #86 on: February 24, 2021, 01:31:34 PM »
I control the spindle speed through mach3?
Logged

Offline TPS

*
  • 2,574 2,574
Re: Mach3, Opt Laser 5W and Aspire
« Reply #87 on: February 24, 2021, 01:37:10 PM »
Quote from: A11an on February 24, 2021, 01:31:34 PM
I control the spindle speed through mach3?
yes, but you control it by using the 0-10V Signal, or am i wrong?
Logged
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline A11an

*
  • 62 62
Re: Mach3, Opt Laser 5W and Aspire
« Reply #88 on: February 24, 2021, 01:39:20 PM »
Oh yes, sorry
Logged

Offline TPS

*
  • 2,574 2,574
Re: Mach3, Opt Laser 5W and Aspire
« Reply #89 on: February 24, 2021, 01:39:33 PM »
the plan is to use the PWM Input of your Laser control
Logged
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.
Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 »   Go Up
« previous next »