Hello Guest it is March 28, 2024, 07:29:30 PM

Author Topic: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A  (Read 68958 times)

0 Members and 1 Guest are viewing this topic.

Offline slvm

*
  •  68 68
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #70 on: June 07, 2015, 05:49:38 AM »
Yesterday I check the inverter, you right Thomas ,is not the same on your link, ....
I adapt 2 relay's to Csmio - Analogoutput 0 (to be able change between CW CCW), after some test the Inverter get into Alarm and block it self, so now Ihave only 2 choiche left:
-to use Analog Output (wiithout any relays) only in to the CW mode  or to change the old-inverter with new one able to be Programmed....

Offline TPS

*
  •  2,501 2,501
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #71 on: June 07, 2015, 06:20:06 AM »
Hi Emil,

maybe you can test with pin4 (input 8) witch is in standard config for
Reverse.

make one test pin4 connected to +24VDC and
one with pin 4 not connected.

let's try and error.

Thomas
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline slvm

*
  •  68 68
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #72 on: June 07, 2015, 06:56:40 AM »
Hi Thomas
Here you find the connector pin from my Inverter, to have one opinion.
Also I post the Limit switches pics disposal on All Axis, the switches +/- are all in one single chain wired, so that made me problem to assign on Mach3 Inputs !? with Home switches is no problem they are separated.

Offline TPS

*
  •  2,501 2,501
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #73 on: June 07, 2015, 07:14:26 AM »
Hi Emil,

for the axis inputs, just seperate them from the e-Stop chain.

they should be NC contacts anyway, not like in the drawing as NO contacts.

Thomas
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline slvm

*
  •  68 68
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #74 on: June 07, 2015, 07:55:47 AM »
You mean use the switch SWX (as example) to input on Mach as + and - Limits for X Axis ? or only for + ?

Offline TPS

*
  •  2,501 2,501
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #75 on: June 07, 2015, 08:57:25 AM »
Yes,

user for example SWX wire it to a input and
cofigure in Port's&Pin's the same inputs fpr X+ and X-.

there is only one switch, but there should be two braket's to trigger it.

Thomas
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline slvm

*
  •  68 68
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #76 on: June 07, 2015, 09:20:44 AM »
got it, thanks. I will look for .

Offline TPS

*
  •  2,501 2,501
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #77 on: June 08, 2015, 07:24:17 AM »
Hello Emil,


good news, got a manual from HSD, bad news (for you), it is in german.

but anyway, the table for connections on page 30 looks quite good,
so i made a small table for connections:

28   (REF-V) 0-10V analog input -> csmio analog output
29    (GND-A) for analog input

5   (in 5) enable inverter -> csmio digital output
4   (REV)  reverse rotation -> csmio digtal output to switch CW/CCW

8   (CM-IN) GND -> 24v GND

1   (FLT-NO) alarm relais -> csmio input inverter ready

2   (FLT-CM) for alarm relaise -> 24V+
6   (EXTFLT) external alarm -> 24V+
22   (IN3)    temperature motor (not used) ->24V+
17   (OUT3-CM) -> 24V+
16   (OUT3-NO) -> csmio input output frq. = 0 allow tool change



30   (CM-OUT) ????? -> csmio input frq. reached but it is a open collector
32   (OUT2)    ????? is connected to 24V+ does not make sence
    
so if only OUT2 is connected i should work with this 30/32 connection.

Thomas
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.

Offline slvm

*
  •  68 68
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #78 on: June 08, 2015, 10:01:43 AM »
thank's a lot Thomas !
It's no problem with the manual language = "Ich spreche auch Deutsch - Zwei Jahre in Deutschland gelebt, im Koblenz"

Offline TPS

*
  •  2,501 2,501
    • View Profile
Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A
« Reply #79 on: June 08, 2015, 02:05:57 PM »
@Hood

are still watching this, to be my second chance ?

Thomas
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.