Hello Guest it is April 18, 2024, 10:29:39 PM
Profile Guest
« previous next »
Pages: 1 2 »   Go Down

Author Topic: Current list of G & M Codes for Lathe  (Read 8231 times)

0 Members and 1 Guest are viewing this topic.

Offline M250cnc

*
  • 591 591
    • View Profile
Current list of G & M Codes for Lathe
« on: September 22, 2009, 07:02:29 AM »
Anyone know where i can get them, done a search but drew a blank

Phil
Logged
The Good Thing About Mach3, Is It's very Configurable

The Bad Thing About Mach3, Is It's Too Configurable

Offline Hood

*
  • 25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: Current list of G & M Codes for Lathe
« Reply #1 on: September 22, 2009, 10:57:39 AM »
Turn manual is the only place I can think of.
Hood
Logged

Offline Dan13

*
  • 1,208 1,208
    • View Profile
    • DY Engineering
Re: Current list of G & M Codes for Lathe
« Reply #2 on: September 22, 2009, 11:41:52 AM »
Don't think such a thing exists. Like Hood said, the Turn manual is the closest thing, but it doesn't mention some codes - like the CSS for instance.

Daniel
Logged

Offline M250cnc

*
  • 591 591
    • View Profile
Re: Current list of G & M Codes for Lathe
« Reply #3 on: September 23, 2009, 04:29:34 AM »
The reason i asked is i was going to make a list for use on the lathe screen similar to what is available for Mill

Phil
Logged
The Good Thing About Mach3, Is It's very Configurable

The Bad Thing About Mach3, Is It's Too Configurable

Offline RICH

*
  • *
  • 7,427 7,427
    • View Profile
Re: Current list of G & M Codes for Lathe
« Reply #4 on: September 23, 2009, 06:17:42 AM »
The Using Mach3TURN MANUAL has a listing, and it includes in the listing lists the Gcode ( associated macro ) for G77  ( M1077.MIS ) and G78 ( M10778.MIS ). If it dosen't list it there I'll  assume that it's not supported.
RICH
Logged

Offline Hood

*
  • 25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: Current list of G & M Codes for Lathe
« Reply #5 on: September 23, 2009, 07:24:37 AM »
As Daniel previously mentioned the only one I can think of that is not in the manual is G48S**** which is used to limit the spindle speed when in CSS.

Hood
Logged

Offline RICH

*
  • *
  • 7,427 7,427
    • View Profile
Re: Current list of G & M Codes for Lathe
« Reply #6 on: September 23, 2009, 07:37:09 AM »
Thanks Hood,
 I created a "cheat cheat" listing of the Gcodes and which will be in an appendix of the LazyTurn Manual. Made a note to include the G48S. 
RICH
Logged

Offline Dan13

*
  • 1,208 1,208
    • View Profile
    • DY Engineering
Re: Current list of G & M Codes for Lathe
« Reply #7 on: September 23, 2009, 07:57:51 AM »
Quote from: Hood on September 23, 2009, 07:24:37 AM
As Daniel previously mentioned the only one I can think of that is not in the manual is G48S**** which is used to limit the spindle speed when in CSS.

Hood

Along with G96 and G97.

I think there were couple of other codes also, but can't remember now.

Daniel
Logged

Offline Hood

*
  • 25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: Current list of G & M Codes for Lathe
« Reply #8 on: September 23, 2009, 08:01:32 AM »
Daniel, G96 and G97 are in the manual, possibly not in the list but they are there.
Hood
Logged

Offline Hood

*
  • 25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: Current list of G & M Codes for Lathe
« Reply #9 on: September 23, 2009, 08:03:46 AM »
Just had a look, its section 6.2.3.1 of th turn manual, certainly doesn't go into much detail though.
Hood
Logged
Pages: 1 2 »   Go Up
« previous next »