Machsupport Forum

Mach Discussion => General Mach Discussion => Topic started by: M250cnc on September 22, 2009, 07:02:29 AM

Title: Current list of G & M Codes for Lathe
Post by: M250cnc on September 22, 2009, 07:02:29 AM
Anyone know where i can get them, done a search but drew a blank

Phil
Title: Re: Current list of G & M Codes for Lathe
Post by: Hood on September 22, 2009, 10:57:39 AM
Turn manual is the only place I can think of.
Hood
Title: Re: Current list of G & M Codes for Lathe
Post by: Dan13 on September 22, 2009, 11:41:52 AM
Don't think such a thing exists. Like Hood said, the Turn manual is the closest thing, but it doesn't mention some codes - like the CSS for instance.

Daniel
Title: Re: Current list of G & M Codes for Lathe
Post by: M250cnc on September 23, 2009, 04:29:34 AM
The reason i asked is i was going to make a list for use on the lathe screen similar to what is available for Mill

Phil
Title: Re: Current list of G & M Codes for Lathe
Post by: RICH on September 23, 2009, 06:17:42 AM
The Using Mach3TURN MANUAL has a listing, and it includes in the listing lists the Gcode ( associated macro ) for G77  ( M1077.MIS ) and G78 ( M10778.MIS ). If it dosen't list it there I'll  assume that it's not supported.
RICH
Title: Re: Current list of G & M Codes for Lathe
Post by: Hood on September 23, 2009, 07:24:37 AM
As Daniel previously mentioned the only one I can think of that is not in the manual is G48S**** which is used to limit the spindle speed when in CSS.

Hood
Title: Re: Current list of G & M Codes for Lathe
Post by: RICH on September 23, 2009, 07:37:09 AM
Thanks Hood,
 I created a "cheat cheat" listing of the Gcodes and which will be in an appendix of the LazyTurn Manual. Made a note to include the G48S. 
RICH
Title: Re: Current list of G & M Codes for Lathe
Post by: Dan13 on September 23, 2009, 07:57:51 AM
As Daniel previously mentioned the only one I can think of that is not in the manual is G48S**** which is used to limit the spindle speed when in CSS.

Hood

Along with G96 and G97.

I think there were couple of other codes also, but can't remember now.

Daniel
Title: Re: Current list of G & M Codes for Lathe
Post by: Hood on September 23, 2009, 08:01:32 AM
Daniel, G96 and G97 are in the manual, possibly not in the list but they are there.
Hood
Title: Re: Current list of G & M Codes for Lathe
Post by: Hood on September 23, 2009, 08:03:46 AM
Just had a look, its section 6.2.3.1 of th turn manual, certainly doesn't go into much detail though.
Hood
Title: Re: Current list of G & M Codes for Lathe
Post by: Dan13 on September 23, 2009, 08:09:01 AM
Hood,

Ok, they ARE mentioned in the manual, but not under the section you'd expect them to be. They are not in the list (like you you noted) or the gcode section, and only mentioned on page 6-2.

Daniel
Title: Re: Current list of G & M Codes for Lathe
Post by: Dan13 on September 23, 2009, 08:10:48 AM
Was typing when you posted your reply ;)

Daniel
Title: Re: Current list of G & M Codes for Lathe
Post by: M250cnc on September 23, 2009, 08:42:24 AM
The Using Mach3TURN MANUAL has a listing, and it includes in the listing lists the Gcode ( associated macro ) for G77  ( M1077.MIS ) and G78 ( M10778.MIS ). If it dosen't list it there I'll  assume that it's not supported.
RICH

Hi Rich

Just had a look and couldn't find it


Phil
Title: Re: Current list of G & M Codes for Lathe
Post by: Hood on September 23, 2009, 08:46:21 AM
The Using Mach3TURN MANUAL has a listing, and it includes in the listing lists the Gcode ( associated macro ) for G77  ( M1077.MIS ) and G78 ( M10778.MIS ). If it dosen't list it there I'll  assume that it's not supported.
RICH

Hi Rich

Just had a look and couldn't find it


Phil

Pg 10-10 and 10-17

Hood
Title: Re: Current list of G & M Codes for Lathe
Post by: M250cnc on September 23, 2009, 09:08:14 AM
Sorry i thought it was in the LazyTurn Manual

Where do i find the Mach3TURN MANUAL  ::)

Phil
Title: Re: Current list of G & M Codes for Lathe
Post by: Hood on September 23, 2009, 09:11:02 AM
Support link at the top of the page.
Hood
Title: Re: Current list of G & M Codes for Lathe
Post by: RICH on September 23, 2009, 09:39:09 AM
Sorry, but the LazyTurn manual is still in developement like the software.  :)
RICH