Hello Guest it is March 29, 2024, 10:57:32 AM

Author Topic: mill retro HELP  (Read 92807 times)

0 Members and 2 Guests are viewing this topic.

Offline Chaoticone

*
  • *
  •  5,624 5,624
  • Precision Chaos
    • View Profile
Re: mill retro HELP
« Reply #100 on: August 06, 2008, 06:29:05 PM »
 ;D

You keep on and you'll be getting beat by the broom.

Brett
;D If you could see the things I have in my head, you would be laughing too. ;D

My guard dog is not what you need to worry about!

Offline Hood

*
  •  25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: mill retro HELP
« Reply #101 on: August 06, 2008, 06:30:15 PM »
;D

You keep on and you'll be getting beat by the broom.

Brett

And you Mr Redneck would probably enjoy that :D

Hood

Offline Chaoticone

*
  • *
  •  5,624 5,624
  • Precision Chaos
    • View Profile
Re: mill retro HELP
« Reply #102 on: August 06, 2008, 06:36:21 PM »
LOL, Whip me, I've been a bad boy...............  ;D

Brett
;D If you could see the things I have in my head, you would be laughing too. ;D

My guard dog is not what you need to worry about!
Re: mill retro HELP
« Reply #103 on: August 06, 2008, 06:52:00 PM »
    :D WHAT A GROUP :D LOL
Ed VanEss
Re: mill retro HELP
« Reply #104 on: August 06, 2008, 11:16:12 PM »
Played with it a bit today, ;D The Machine, what else. ;D Ran it thru a bolt hole circle and a circular pocket
without the Z axis.
Everything worked great, Still have to set up my homing and limits.Then comes the spindle.
Later
Ed
Ed VanEss
Re: mill retro HELP
« Reply #105 on: August 07, 2008, 03:54:56 PM »
Hood ,
Where do I set debounce , and what should it be set at?
Thanks
 Ed
Ed VanEss

Offline Hood

*
  •  25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: mill retro HELP
« Reply #106 on: August 07, 2008, 04:12:35 PM »
Ideally debounce should be as low as possible, not sure what mine is, probably the default which I think is 500 as I dont think I ever set it.
You will get it from Config Tab then General config, its top right.
Hood

Offline Chip

*
  • *
  •  2,055 2,055
  • Gainesville Florida USA
    • View Profile
Re: mill retro HELP
« Reply #107 on: August 07, 2008, 04:16:52 PM »
Hi, Ed

It's on the Gen-Config page top right, It's setting can be from 0- 2000 or so mostly to weed-out spurious noise on Input's.

Maybe Hood is recovering from all the Abuse, B--r--e--t--t.....LOL.......?

Chip

Hood, I only live 5-6 hrs. from Brett let me Now, I have Duct-Tape
« Last Edit: August 07, 2008, 04:20:54 PM by Chip »

Offline Hood

*
  •  25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: mill retro HELP
« Reply #108 on: August 07, 2008, 04:23:06 PM »
Would take a lot more than duct tape to cover that huge orifice :D

Hood
Re: mill retro HELP
« Reply #109 on: August 07, 2008, 04:34:24 PM »
I could always send my wife down to see Brett.  :D

I just checked debounce, its set at 0.

Thanks
Ed
Ed VanEss