Here is what came with the mpg pendant

Hi Cad cam man,

It would be helpful for easy viewing if you would resize your pictures to 800 x 600 before posting. This thread refers; https://www.machsupport.com/forum/index.php?topic=24585.0

Many thanks,

Tweakie.

according to the example from my link wiring would be:

yellow -> Pin 3
yellow/black -> Pin 4
Brown -> Pin 5
Brown/black -> Pin 6

gray -> Pin 7
gray/black -> Pin 8
orange -> Pin 9

orange/black -> Pin 25

green -> Pin 13
White -> Pin 15
red -> Pin 10
black - Pin 24

the you can use all Settings from example

@tweakie sorry I didnt know there was a preference of size picture to post .. I will be sure to resize them in the future...

@ tps.. so are you saying I should rewire my whole pendant to match the example you posted ?? The wire color does not matter as long as I know what colors go where and they all match up according to the example in reply #10

@ tps.. so are you saying I should rewire my whole pendant to match the example you posted ?? The wire color does not matter as long as I know what colors go where and they all match up according to the example in reply #10

for the Moment i am not able to follow you, how the pedant is wired on the PP port side??!

Sorry for the confusion I have the pendant wired just like the instructions that came with it as.
Red - +5v( outside source )
Black - gnd ( outside source)

Green- 2 pin ( mpg A+)
White- 3 pin ( mpg B+ )
Green&black- 1 pin ( jog on led +5v )
White&black- gnd ( jog on led gnd)
Yellow- 4 pin ( select x axis )
Yellow&black- 5 pin ( select y axis )
Brown- 6 pin ( select z axis )
Brown&black- 7pin ( select a axis )
Gray- 8pin ( x1 )
Gray&black- 9pin ( x10 )
Orange- 10pin ( x100 )
Orange&black- +5v ( com for selector )

All the other color and number not listed above are not being used and have nothing connected to them
I hope this clears it up for you

GND from outside source and GND of your Parallel port should be connected or your encoder outputs will be referenced to what?

Green- 2 pin ( mpg A+)
White- 3 pin ( mpg B+ )
Config -> Ports&Pins -> Encoder/MPS -> MPG1 Enabled | A-Port = 2 | A-Pin = 2 | B-Port = 2 | B-Pin = 3

Green&black- 1 pin ( jog on led +5v )
White&black- gnd ( jog on led gnd)

this is only the led, we will take care later


Yellow- 4 pin ( select x axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 4
System Hotkeys -> Trigger#1 OEM Code = 259

Yellow&black- 5 pin ( select y axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#2 Enabled | Port = 2 | Pin = 5
System Hotkeys -> Trigger#1 OEM Code = 260

Brown- 6 pin ( select z axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 6
System Hotkeys -> Trigger#1 OEM Code = 261

Brown&black- 7pin ( select a axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 7
System Hotkeys -> Trigger#1 OEM Code = 262


Gray- 8pin ( x1 )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 8
System Hotkeys -> Trigger#1 OEM Code = 265

Gray&black- 9pin ( x10 )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 9
System Hotkeys -> Trigger#1 OEM Code = 266

Orange- 10pin ( x100 )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 10
System Hotkeys -> Trigger#1 OEM Code = 267

Orange&black- +5v ( com for selector )
this is wrong, Needs to be connected to GND

and as ZASTo sayed

GND from outside source and GND of your Parallel port should be connected pin 18-25

TPS, you "messed up" a bit

        Personal Message (Offline)

Re: Plugin that works for Chinese mpg pendant
« Reply #17 on: 19-01-2020, 10:57:31 »

Green- 2 pin ( mpg A+)
White- 3 pin ( mpg B+ )
Config -> Ports&Pins -> Encoder/MPS -> MPG1 Enabled | A-Port = 2 | A-Pin = 2 | B-Port = 2 | B-Pin = 3

Green&black- 1 pin ( jog on led +5v )
White&black- gnd ( jog on led gnd)

this is only the led, we will take care later


Yellow- 4 pin ( select x axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 4
System Hotkeys -> Trigger#1 OEM Code = 259

Yellow&black- 5 pin ( select y axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#2 Enabled | Port = 2 | Pin = 5
System Hotkeys -> Trigger#1 OEM Code = 260

Brown- 6 pin ( select z axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 6
System Hotkeys -> Trigger#1 OEM Code = 261

Brown&black- 7pin ( select a axis )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 7
System Hotkeys -> Trigger#1 OEM Code = 262


Gray- 8pin ( x1 )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 8
System Hotkeys -> Trigger#1 OEM Code = 265

Gray&black- 9pin ( x10 )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 9
System Hotkeys -> Trigger#1 OEM Code = 266

Orange- 10pin ( x100 )
Config -> Ports&Pins -> Input Signal -> OEMTrigger#1 Enabled | Port = 2 | Pin = 10
System Hotkeys -> Trigger#1 OEM Code = 267

Orange&black- +5v ( com for selector )
this is wrong, Needs to be connected to GND

Same OEMTrigger on different pins
I know, it is a Copy/Paste common error