Hello Guest it is March 29, 2024, 07:31:59 AM

Author Topic: UC300  (Read 2618 times)

0 Members and 1 Guest are viewing this topic.

UC300
« on: June 26, 2019, 09:44:05 AM »
WHAT IS THE DIFFERENCE BETWEEN UC300 AND UC100  MOTION CONTROLLERS?? I USE THE UC100

LUMBER60

Offline Tweakie.CNC

*
  • *
  •  9,196 9,196
  • Super Kitty
    • View Profile
Re: UC300
« Reply #1 on: June 26, 2019, 09:57:32 AM »
Perhaps check out the uccnc website, they describe the differences quite well. https://www.cncdrive.com/products.html

Tweakie.
PEACE
Re: UC300
« Reply #2 on: June 26, 2019, 10:06:27 AM »
Thanks

Offline ger21

*
  • *
  •  6,295 6,295
    • View Profile
    • The CNC Woodworker
Re: UC300
« Reply #3 on: June 26, 2019, 06:45:02 PM »
The UC100 has the equivalent pins of one parallel port.
The UC300ETH has 5x the inputs and outputs, has an ethernet connection, higher pulse frequency, and analog inputs and outputs.
Gerry

2010 Screenset
http://www.thecncwoodworker.com/2010.html

JointCAM Dovetail and Box Joint software
http://www.g-forcecnc.com/jointcam.html
Re: UC300
« Reply #4 on: June 27, 2019, 07:56:33 AM »
thanks, that seems like the way to go. That will probably be my next upgrade.

lumber60

Offline ger21

*
  • *
  •  6,295 6,295
    • View Profile
    • The CNC Woodworker
Re: UC300
« Reply #5 on: June 27, 2019, 08:45:27 AM »
If you don't need as many ports and pins as the UC300ETH offers, you might want to consider the AXBB-E, which is an all in one breakout board controller.
The UC300ETH requires a breakout board for each port, or a multi port breakout board.
The AXBB-E has screw terminals for all the pins.
Gerry

2010 Screenset
http://www.thecncwoodworker.com/2010.html

JointCAM Dovetail and Box Joint software
http://www.g-forcecnc.com/jointcam.html
Re: UC300
« Reply #6 on: June 27, 2019, 09:17:26 AM »
aah yes information is the key. I will investigate that as well.
Thanks,

lumber60
Re: UC300
« Reply #7 on: June 27, 2019, 09:21:43 AM »
CNC DRIVE SITE MENTIONS MACH 3, WILL THIS AXBB-E FUNCTION WITH MACH 4?

LUMBER60

Offline ger21

*
  • *
  •  6,295 6,295
    • View Profile
    • The CNC Woodworker
Re: UC300
« Reply #8 on: June 27, 2019, 10:01:39 AM »
I would email them and ask the status of a Mach4 plugin. I would expect that they are working on it.
You might also ask them if there are any features that their Mach4 plugins don't support.
Gerry

2010 Screenset
http://www.thecncwoodworker.com/2010.html

JointCAM Dovetail and Box Joint software
http://www.g-forcecnc.com/jointcam.html
Re: UC300
« Reply #9 on: June 27, 2019, 10:12:27 AM »
GOT IT,

THANKS
LUMBER60