Hello Guest it is December 08, 2021, 01:58:58 AM

Author Topic: X Y axis move togehter with Arrows key  (Read 6062 times)

0 Members and 1 Guest are viewing this topic.

Re: X Y axis move togehter with Arrows key
« Reply #30 on: February 25, 2018, 06:52:38 AM »
Hi,
yes they are much better.

It looks like your motor outputs are correct.  The layout of the signals suggests
X axis step=pin2
          dir=pin3
Y axis step=pin5
          dir=pin6
Z axis step=pin8
          dir=pin9

Your spindle assignments look wrong
Spindle step=pin16
             dir=pin14

One thing I think you should change is on the Outputs page
X enable=pin4
Y enable=pin4
Z enable=pin4

Craig
My wife left with my best friend...
     and I miss him!
Re: X Y axis move togehter with Arrows key
« Reply #31 on: February 25, 2018, 07:19:17 AM »
Thanks Craig I'll do the same and get back to shortly..
regards,
DD
Re: X Y axis move togehter with Arrows key
« Reply #32 on: February 25, 2018, 07:29:24 AM »
I changed the Pin numbers as you suggested but the same condition....
regards,
DD
Re: X Y axis move togehter with Arrows key
« Reply #33 on: February 25, 2018, 12:30:38 PM »
Hi,
I can only conclude that the board is faulty.

Take it up with the peron you bought it from to replace it.

Craig
My wife left with my best friend...
     and I miss him!
Re: X Y axis move togehter with Arrows key
« Reply #34 on: February 26, 2018, 01:40:25 AM »
Hi Craig,
One of my friend also bought the same machine with same controller let me borrow his controller and check on my machine, i'll update you in few hours.
regards,
DD
Re: X Y axis move togehter with Arrows key
« Reply #35 on: February 26, 2018, 12:33:31 PM »
I changed the controller and checked the second controller pins configuration it was 100% same as mine and after changing the controller the same result nothing changes How it's possible if my controller is faulty his should be ok ..
Re: X Y axis move togehter with Arrows key
« Reply #36 on: February 26, 2018, 12:48:51 PM »
Hi,
yes that would tend to indicate that Mach is causing the X and Y axes move together.

Try MDIing some separate X and Y moves:

G0 X50
X0
Y50
Y0

That should move X 50mm then back again, then Y 50mm and back again. Does it do that or do both axes move together?
When the axes move together do both the X&Y DROs change together?

Does your friend have his machine set up and running?

Craig
My wife left with my best friend...
     and I miss him!
Re: X Y axis move togehter with Arrows key
« Reply #37 on: February 26, 2018, 01:26:21 PM »
Ok Craig I'll do the same and about my friend he is not using his machine since last 15 days but as per him he was not facing the problem i am facing..
I'll update you tomorrow ..
regards, DD
Re: X Y axis move togehter with Arrows key
« Reply #38 on: February 26, 2018, 01:44:16 PM »
could you please put your used profile (xx.XML) here?

Klaus
The brain isn't a soap, it doesn't shrink when used.
Re: X Y axis move togehter with Arrows key
« Reply #39 on: February 27, 2018, 02:06:54 AM »
Hi Klaus,
I am not technically sound in this machine so didn't understand can you please elaborate ?
regards,
DD