Hello Guest it is November 15, 2019, 05:39:42 PM

Author Topic: MACH3PLASMA LIMIT SWITCHES FOR G540/PROMA  (Read 12779 times)

0 Members and 2 Guests are viewing this topic.

Offline Davek0974

*
  •  2,580 2,580
    • View Profile
    • DD Metal Products Ltd
Re: MACH3PLASMA LIMIT SWITCHES FOR G540/PROMA
« Reply #160 on: February 27, 2018, 04:48:10 PM »
Pierce height should be in the g-code IIRC
Bridgeport Mill, Mach3 V062, CSMIO-IP/A controller, AC Servo Drives
Re: MACH3PLASMA LIMIT SWITCHES FOR G540/PROMA
« Reply #161 on: February 27, 2018, 04:53:46 PM »
MACH is applying random numbers to my Z offset. I don’t know what is going on
Re: MACH3PLASMA LIMIT SWITCHES FOR G540/PROMA
« Reply #162 on: February 27, 2018, 04:57:12 PM »
The probe isn’t operating correctly anymore, it’s not raising Z to go to pierce height after probing, it’s driving down into the material.

Offline TPS

*
  •  1,407 1,407
    • View Profile
Re: MACH3PLASMA LIMIT SWITCHES FOR G540/PROMA
« Reply #163 on: February 27, 2018, 05:36:18 PM »
ok let's get back to the Basics,

open up vb scirper window

copy this code:

pierceHeight = 0.5 'enter here a value for wanted pierceheiht


   code "F30"
   code "G31 Z-1"
   While Ismoving()
   Wend

   code "G00 Z" & GetVar(2002) 'go back to the  probepoint
   While Ismoving()
   Wend

   code "G91 Z-" & pierceHeight
   While Ismoving()
   Wend

   code "G92 Z0"
   While Ismoving()
   Wend

   Code "G90"

and use the ||> green buton to se what's goinng on
anything is possible, just try it.
if you find some mistakes, in my bad bavarian english,they are yours.
Re: MACH3PLASMA LIMIT SWITCHES FOR G540/PROMA
« Reply #164 on: February 27, 2018, 06:11:48 PM »
It probes good, then dives at g91. I changed 2002 to 0, then re ran, it got all the way passed g91 z- (at this point it was back at Z 0) then it dove .5” down instead of rising .5” up

Offline TPS

*
  •  1,407 1,407
    • View Profile
Re: MACH3PLASMA LIMIT SWITCHES FOR G540/PROMA
« Reply #165 on: February 28, 2018, 01:59:14 AM »
sorry should be

code "G91 Z" & pierceHeight
anything is possible, just try it.
if you find some mistakes, in my bad bavarian english,they are yours.
Re: MACH3PLASMA LIMIT SWITCHES FOR G540/PROMA
« Reply #166 on: February 28, 2018, 11:22:19 AM »
That fixed the probing issue, still having the same issue with the THC.

Offline TPS

*
  •  1,407 1,407
    • View Profile
Re: MACH3PLASMA LIMIT SWITCHES FOR G540/PROMA
« Reply #167 on: February 28, 2018, 11:46:25 AM »
is Torch DN in dignosic Screen defenitiv off?
anything is possible, just try it.
if you find some mistakes, in my bad bavarian english,they are yours.
Re: MACH3PLASMA LIMIT SWITCHES FOR G540/PROMA
« Reply #168 on: February 28, 2018, 11:47:15 AM »
Really interesting, on my second pierce, when it goes to probe it changed my cutting speed From 130 ipm  to 30 ipm.?
Re: MACH3PLASMA LIMIT SWITCHES FOR G540/PROMA
« Reply #169 on: February 28, 2018, 11:48:32 AM »
is Torch DN in dignosic Screen defenitiv off?

I don’t understand.. sorry