Hello Guest it is April 11, 2021, 08:56:13 PM

Author Topic: Csmio/IP-A drives  (Read 16876 times)

0 Members and 1 Guest are viewing this topic.

Offline Hood

*
  •  25,838 25,838
  • Carnoustie, Scotland
    • View Profile
Re: Csmio/IP-A drives
« Reply #30 on: March 26, 2015, 06:10:59 AM »
If the encoders are 5v square wave differential then it will not be a problem. If they are single ended then it would be best to get a line driver to make them differential.

Hood
Re: Csmio/IP-A drives
« Reply #31 on: March 26, 2015, 06:13:54 AM »
Yes hood it's bidirectional 5v square wave.
Regards ,
Basim

Offline Hood

*
  •  25,838 25,838
  • Carnoustie, Scotland
    • View Profile
Re: Csmio/IP-A drives
« Reply #32 on: March 26, 2015, 06:17:26 AM »
It should work fine then as it will basically be the same as the original control, motors Tachs to drives for speed feedback and encoders to control (IP-A in this case) for position feedback. :)


Hood
Re: Csmio/IP-A drives
« Reply #33 on: March 26, 2015, 06:28:33 AM »
Hood,
is it mean that the settinng the PID could be easier than AC servos without Tachometer??

i want to start my job with the axes!!

please advice,
ghantos

Offline Hood

*
  •  25,838 25,838
  • Carnoustie, Scotland
    • View Profile
Re: Csmio/IP-A drives
« Reply #34 on: March 26, 2015, 06:40:06 AM »
It should just be the same, the AC servos normally use the encoder for speed feedback although some use resolvers but essentially the tuning of a DC will be the same as an AC as far as the IP-A is concerned.

Hood
Re: Csmio/IP-A drives
« Reply #35 on: March 26, 2015, 06:55:05 AM »
Thanks Alot Hood,

Now, i want to start with the axes motions and later to pin out the Inputs And Outputs.....

from your experience, whitch importand switches i need to pin out in Mach3 for begining??
is the Estop is enught at this level.

the problem that in the manual we have good information, but the sequnce and the order of telling the information is not good.
sometimes explaining the I/O then GO to Encoder after that return back to I/O.
its really confusing me.

i will install the mach3 at first then installing the plugin and then wiring then tunning.
what do you thing?
 Ghantos

Offline Hood

*
  •  25,838 25,838
  • Carnoustie, Scotland
    • View Profile
Re: Csmio/IP-A drives
« Reply #36 on: March 26, 2015, 09:13:46 AM »
Really wiring  will be dependant on your machine but definitely an E-Stop is a must and preferably it should work on the hardware side of things as well, ie drop out contactors or similar so that the drives are powered down. You want to keep the encoders power connected though as it will mean the IP-A and Mach will still know where the axes are even after an E-Stop.

Hood
Re: Csmio/IP-A drives
« Reply #37 on: March 26, 2015, 02:21:19 PM »
Hello hood,
I have rade that the firmware version of the csmio/A and the plugin from mach 3 must be the same !!
My newest firmware of the controller is 2.063 and the last version of the plug in on mach3 website is 1.65.

No new versions their !!!
How we can match between !!
Regards
Ghantos

Offline Hood

*
  •  25,838 25,838
  • Carnoustie, Scotland
    • View Profile
Re: Csmio/IP-A drives
« Reply #38 on: March 26, 2015, 02:31:56 PM »
The plugin comes from CS-Lab and not Mach.
When you download the installer from CS-Lab it updates the firmware and at the same time installs the correct plugin. So if you have the latest firmware you should also already have the correct plugin.

Hood

Offline TPS

*
  •  2,097 2,097
    • View Profile
Re: Csmio/IP-A drives
« Reply #39 on: March 26, 2015, 02:34:19 PM »
if you install this:

http://www.cs-lab.eu/en/upload/firmware/setup_CSMIO-IP-A-2.603.zip

you get all you Need.

Thomas
anything is possible, just try to do it.
if you find some mistakes, in my bad bavarian english,they are yours.