Hello Guest it is October 14, 2019, 05:28:02 PM

Author Topic: NEW: 'Official' PoKeys Mach3 Plugin - 'alpha' version v0.01  (Read 42898 times)

0 Members and 1 Guest are viewing this topic.

Offline Hood

*
  •  25,855 25,855
  • Carnoustie, Scotland
    • View Profile
Re: NEW: 'Official' PoKeys Mach3 Plugin - 'alpha' version v0.01
« Reply #40 on: April 14, 2012, 05:58:46 AM »
I have just tried with the USB version and it is working as it should :)
Hood
Re: NEW: 'Official' PoKeys Mach3 Plugin - 'alpha' version v0.01
« Reply #41 on: April 20, 2012, 09:49:33 AM »
I have also a problem with the index, encoder with Pokey 56E.
When i  "Enable the encoder", the counter seems to count ok.
But when i aslo activate "Enable reset on index" the count value is not correct, is not counting enough.
When i put the pokey input to ground, then the count value is reset.
I am reading the RAW values from the pokey config program. (so at the moment without Mach3)

Offline NeoTO

*
  •  504 504
    • View Profile
    • PoLabs
Re: NEW: 'Official' PoKeys Mach3 Plugin - 'alpha' version v0.01
« Reply #42 on: April 20, 2012, 09:54:14 AM »
This one is in the 'investigation' already.
www.poscope.com home of PoKeys USB HID, IO, USB, Ethernet controler and PoScope USB PC oscilloscope

Offline LWW

*
  •  1 1
    • View Profile
Re: NEW: 'Official' PoKeys Mach3 Plugin - 'alpha' version v0.01
« Reply #43 on: April 24, 2012, 04:00:58 AM »
The old plug-in not used? How now it is possible to show DRO-1000 on the screen?

Offline NeoTO

*
  •  504 504
    • View Profile
    • PoLabs
Re: NEW: 'Official' PoKeys Mach3 Plugin - 'alpha' version v0.01
« Reply #44 on: April 24, 2012, 04:41:45 AM »
The old plug-in not used? How now it is possible to show DRO-1000 on the screen?

What are you referring to? Give more details on what you would like to know.
www.poscope.com home of PoKeys USB HID, IO, USB, Ethernet controler and PoScope USB PC oscilloscope
Re: NEW: 'Official' PoKeys Mach3 Plugin - 'alpha' version v0.01
« Reply #45 on: November 19, 2012, 01:36:06 PM »
I made a pendant:



using Pokeys. On old plugin i have drive LCD with macropump.
I saw that you have made new plugin, so i decide to upgrade Pokeys FW,
 and install new mach3 plugin. Than i encounter problems with writing to LCD.
I have set lcd plugin to secondary pins (28-34) because of previous pendant setup.
Now the buttons and MPG are working, but i dont get any content to LCD.
I have setup plugin like that:






« Last Edit: November 19, 2012, 01:44:32 PM by germil »

Offline NeoTO

*
  •  504 504
    • View Profile
    • PoLabs
Re: NEW: 'Official' PoKeys Mach3 Plugin - 'alpha' version v0.01
« Reply #46 on: November 20, 2012, 01:45:17 AM »
Hi, Milan

We are working on supporting the LCD on PoKeys55. PoKeys56 series use a new buffered LCD mode, which is used in Mach3 plugin to improve speed.

Regards,
Matevž
www.poscope.com home of PoKeys USB HID, IO, USB, Ethernet controler and PoScope USB PC oscilloscope
Re: NEW: 'Official' PoKeys Mach3 Plugin - 'alpha' version v0.01
« Reply #47 on: November 20, 2012, 04:02:03 AM »
Thank you Matevž.
Best regards,
Milan