Hello Guest it is March 28, 2024, 04:23:05 PM

Author Topic: OK that does it!  (Read 18919 times)

0 Members and 1 Guest are viewing this topic.

Offline Whacko

*
  •  239 239
  • Happy Days
    • View Profile
OK that does it!
« on: December 24, 2007, 10:09:29 AM »
Ok, this is it! MERRY XMAS TO ALL!!!

Whacko on holiday!!!!
Nothing's impossible

Offline Hood

*
  •  25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: OK that does it!
« Reply #1 on: December 24, 2007, 05:37:30 PM »
Ok, this is it! MERRY XMAS TO ALL!!!

Whacko on holiday!!!!

SLACKER!!!!!!!!
:D

Offline Whacko

*
  •  239 239
  • Happy Days
    • View Profile
Re: OK that does it!
« Reply #2 on: December 25, 2007, 02:10:04 AM »
Ok, this is it! MERRY XMAS TO ALL!!!

Whacko on holiday!!!!

I Gotto slacker, otherwise I might cracka! LOL!

Whacko

SLACKER!!!!!!!!
:D
Nothing's impossible

Offline jimpinder

*
  •  1,232 1,232
  • Wakefield, West Yorks, UK
    • View Profile
Re: OK that does it!
« Reply #3 on: December 25, 2007, 08:30:46 AM »
You stopped a bit early - it wasn't even Christmas day :D
Not me driving the engine - I'm better looking.

Offline Whacko

*
  •  239 239
  • Happy Days
    • View Profile
Re: OK that does it!
« Reply #4 on: December 25, 2007, 11:32:18 AM »
It's all relative, you know. Space time. The empty space between my ears and the time I take to fill an empty (void)

Happy holidays!
Whacko
Nothing's impossible

Offline Whacko

*
  •  239 239
  • Happy Days
    • View Profile
Re: OK that does it!
« Reply #5 on: December 25, 2007, 02:52:25 PM »
OK I lied, I'm back! These folks at home are all tanked up, it got boring, so I'm bright eyed and bushy tailed and they are vocally impaired!

Whacko
Nothing's impossible
Re: OK that does it!
« Reply #6 on: December 25, 2007, 03:43:38 PM »
Welcome back Whacko, (you seem bored an anxious to help.)
I've got a question for ya. I'm running Mach3 Turn... Thread cutting with the wizard and hand writing the code.. How can I make the threading tool pull out,(X pos.), and not leave a 60 deg. groove at the end of the thread ? Seems like whatever I do, I can't make it look like I cut it manually. I have double nuts on the ball screw and ZERO backlash but can't make it pull out right. 
Thanks Whacko, or anyone else.
RC

I tried rpm from 1300 , 700,  and  400.... all the same. Also varied the pull-out angle. No change.
Would like to extend each pass, (Z-) but don't know how...???
« Last Edit: December 25, 2007, 03:54:06 PM by Overloaded »

Offline Whacko

*
  •  239 239
  • Happy Days
    • View Profile
Re: OK that does it!
« Reply #7 on: December 25, 2007, 03:52:41 PM »
Old habits die hard. I was a lecturer, seems I still want to lecture! LOL! Can you post one of your nc part programs? Let's have a look.

Whacko
Nothing's impossible
Re: OK that does it!
« Reply #8 on: December 25, 2007, 03:56:27 PM »
SURE !
I gotta run out to the shop and copy it...................................be right back. DON"T GO NOWHERE!
Re: OK that does it!
« Reply #9 on: December 25, 2007, 04:05:19 PM »
Here


« Last Edit: December 26, 2007, 10:41:52 AM by Overloaded »