Hello Guest it is November 15, 2019, 03:28:38 PM

Author Topic: mach3 +nema23+tbb6600  (Read 1923 times)

0 Members and 1 Guest are viewing this topic.

Re: mach3 +nema23+tbb6600
« Reply #20 on: May 10, 2019, 04:32:19 AM »
hola  bueno pues el tema del mach3 ya esta resuelto gracias por la ayuda

Offline Tweakie.CNC

*
  • *
  •  7,997 7,997
  • Super Kitty
    • View Profile
    • Tweakie.CNC
Re: mach3 +nema23+tbb6600
« Reply #21 on: May 10, 2019, 04:36:03 AM »
Excellent   :)
Success consists of going from failure to failure without loss of enthusiasm.  Winston Churchill.
Re: mach3 +nema23+tbb6600
« Reply #22 on: May 10, 2019, 05:08:27 AM »
no se si este problema pueden ayudar aqui la verdad que esto del cnc es un problema de tras de otro jeje pero espero superar con ayuda
creo que no se configurar bien mi spindl por que me pasa esto a continuación envía documentos por si alguien puede aconsejar
https://www.youtube.com/watch?v=Bp_MiCEkEvM

Offline reuelt

*
  •  444 444
    • View Profile
Re: mach3 +nema23+tbb6600
« Reply #23 on: May 14, 2019, 06:57:40 PM »
ERR 6 = over current protection
I think water pump is probably not installed or too small.
flow rate of 3500 l/min is required for 1500w spindle.

Lowest frequency normally (P07) = 0 Hz   
Highest frequency normally (P06) = 400Hz


"the gift of God is eternal life through Jesus Christ our Lord"
Re: mach3 +nema23+tbb6600
« Reply #24 on: May 15, 2019, 03:18:07 AM »
hola gracias por respuesta error 6 solucionado    ahora error 1   es complicado mil pruebas y cuando reparo un error sale otro  :-\ :-\
https://www.youtube.com/watch?v=oQ_3wdiUmy0
Re: mach3 +nema23+tbb6600
« Reply #25 on: May 15, 2019, 05:46:21 AM »
hola ya lo pude solucionar
gracias
https://www.youtube.com/watch?v=5GZkc7M-en0
Re: mach3 +nema23+tbb6600
« Reply #26 on: October 15, 2019, 02:48:44 PM »
como pregunto en este forum? que hago para plantear mi problema?
por favor
Re: se come parte del programa
« Reply #27 on: October 16, 2019, 11:31:40 AM »
con bobcadcam genero el codigo G para un gravado en relieve desde una imagen, en tres ejes. el avance del programa es cada 0.3 mm en X. se salta de una X, digamos X-250 a X-500. no ejecuta los comando de Y ni Z si no que continúa en X-250.3 realizando los comandos Y y Z correspondientes a X-500. esto lo hace en varios puntos de X.
vuelvo a correr el mismo programa y los saltos los ejecuta en diferentes Xs.
espero me haya explicado y entiendan mi problema.
pueden sugerirme las o la causa?

Offline Tweakie.CNC

*
  • *
  •  7,997 7,997
  • Super Kitty
    • View Profile
    • Tweakie.CNC
Re: mach3 +nema23+tbb6600
« Reply #28 on: October 17, 2019, 01:31:53 AM »
Quote
With bobcadcam I generate the G code for embossing from an image, on three axes. The progress of the program is every 0.3 mm in X. It jumps from an X, say X-250 to X-500. It does not execute the Y or Z commands, but continues in X-250.3 by performing the Y and Z commands corresponding to X-500. This he does in several points of X.
I run the same program again and the jumps are executed in different Xs.
I hope you have explained to me and understand my problem.
Can you suggest the cause?

Hi Fernado,

Can you check that you are using a genuine Mach3 license.

(If you are using an invalid, cracked, or hacked license, Mach may intentionally corrupt your data so as to not let you use your equipment).


Tweakie.
« Last Edit: October 17, 2019, 01:34:52 AM by Tweakie.CNC »
Success consists of going from failure to failure without loss of enthusiasm.  Winston Churchill.

Offline ZASto

*
  •  185 185
    • View Profile
Re: mach3 +nema23+tbb6600
« Reply #29 on: October 17, 2019, 05:37:21 AM »
There are some blacklisted licenses known to Mach3.
Extracted from .062 executable:

Schopler    Juberian    Allison Scanners    bassam  PAPA FABIO  Ivan Todosijevic    Sompob  Advanced Control Tech (ACT) MaoA~A ¯Ðtonar rebecca crans   Vortech CNC Jeff Sandstrom  Maksim Amvtonar

Sorry for unformated text.

These licenses appear to work, but as far as I heard, can produce some quirks:) What the quirks are, I don't know exactly, but as far as I've heard, "tool breakage" in canned drill cycles ... (movement to next hole to be drilled without lifting tool out of already drilled hole.
Make no mistake between my personality and my attitude.
My personality is who I am.
My attitude depends on who you are.