Hello Guest it is April 22, 2021, 03:58:08 PM

Author Topic: X Y axis move togehter with Arrows key  (Read 5042 times)

0 Members and 1 Guest are viewing this topic.

Re: X Y axis move togehter with Arrows key
« Reply #50 on: March 01, 2018, 06:08:59 AM »
Hi Roger

you're rigth. But the profiles I got were opposite. Keys up / down were 39 37 which is x-direction.

Klaus
The brain isn't a soap, it doesn't shrink when used.

Offline rcaffin

*
  •  1,035 1,035
    • View Profile
Re: X Y axis move togehter with Arrows key
« Reply #51 on: March 01, 2018, 06:15:50 AM »
Does that explain why X & Y were moving together though?

Strange stuff ...

Cheers
Roger
Re: X Y axis move togehter with Arrows key
« Reply #52 on: March 01, 2018, 06:32:27 AM »

Yes, but only if "Emulated" is also checked.


Klaus
The brain isn't a soap, it doesn't shrink when used.

Offline rcaffin

*
  •  1,035 1,035
    • View Profile
Re: X Y axis move togehter with Arrows key
« Reply #53 on: March 01, 2018, 03:36:26 PM »
Bugs maybe in the version OP is using?

Cheers
Roger
Re: X Y axis move togehter with Arrows key
« Reply #54 on: March 01, 2018, 03:58:40 PM »
Hi

I don't think so. You can test it with the standard screen 1024.set. Just change the settings, in the "Port Setup and Axis Selection". I tested on Win10 Mach3 V3.043.062 without a parallel port and could see the x and y movement on the DRO's.

Klaus
« Last Edit: March 01, 2018, 04:00:27 PM by Klaus1311 »
The brain isn't a soap, it doesn't shrink when used.

Offline rcaffin

*
  •  1,035 1,035
    • View Profile
Re: X Y axis move togehter with Arrows key
« Reply #55 on: March 01, 2018, 04:11:47 PM »
Hi Klaus

I am not sure what I should be looking for, or what settings I should be changing. I fiddled around a bit with enabling/disabling the ports on my desk PC but the correct DROs still changed as expected with the arrow keys.
Ah - I do not have a pendant on my desk machine. But the pendant I use on the actual machine works fine.

What am I missing? Suggestions?

Cheers
Roger
Re: X Y axis move togehter with Arrows key
« Reply #56 on: March 01, 2018, 04:27:11 PM »
Hi Roger,

I also don't have a pendant. Try the following:
Ports and Pins -> Input Signals
Jog X++    Enabled Emulated Hotkey 38 (arrow up)
Jog X--      Enabled Emulated Hotkey 40 (arrow down)
Jog Y++    Enabled Emulated Hotkey 39 (arrow right)
Jog Y--      Enabled Emulated Hotkey 37 (arrow left)

Apply
Reset
occasionally I had to change the Jog mode with the fly out dialog
Jogging with the arrow keys up, down, left or riight show x and y movement on the DRO's

Klaus
« Last Edit: March 01, 2018, 04:28:44 PM by Klaus1311 »
The brain isn't a soap, it doesn't shrink when used.
Re: X Y axis move togehter with Arrows key
« Reply #57 on: March 02, 2018, 10:13:57 AM »
Hi Roger,

I also don't have a pendant. Try the following:
Ports and Pins -> Input Signals
Jog X++    Enabled Emulated Hotkey 38 (arrow up)
Jog X--      Enabled Emulated Hotkey 40 (arrow down)
Jog Y++    Enabled Emulated Hotkey 39 (arrow right)
Jog Y--      Enabled Emulated Hotkey 37 (arrow left)

Apply
Reset
occasionally I had to change the Jog mode with the fly out dialog
Jogging with the arrow keys up, down, left or riight show x and y movement on the DRO's

Klaus
THANKS ALOT KLAUS....PROBLEM SOLVED
Re: X Y axis move togehter with Arrows key
« Reply #58 on: March 02, 2018, 10:16:51 AM »
Thanks everyone///Thanks for your support ...Craig , Klaus , Roger ..... problem solved by assigning corresponding  Hotkeys...