Hello Guest it is May 09, 2025, 02:49:56 PM
Profile Guest
« previous next »
Pages: « 1 2 3 4 5 »   Go Down

Author Topic: LOVING the PMC!! Thanks Steve!!!  (Read 30794 times)

0 Members and 1 Guest are viewing this topic.

Offline thespindoctor

*
  • 307 307
    • The Spin Doctor
Re: LOVING the PMC!! Thanks Steve!!!
« Reply #30 on: November 20, 2016, 06:39:14 PM »
Where is the PMC to be found and any docs on it?

Thanks
Keith
Logged

Offline TOTALLYRC

*
  • 861 861
Re: LOVING the PMC!! Thanks Steve!!!
« Reply #31 on: November 20, 2016, 07:05:59 PM »
You need  Mach4 version 4 ******************.3112. Under configure select PMC. Docs are in the mach4 doc folder, PMC.


Mike
Logged
We never have the time or money to do it right the first time, but we somehow manage to do it twice and then spend the money to get it right.

Offline thespindoctor

*
  • 307 307
    • The Spin Doctor
Re: LOVING the PMC!! Thanks Steve!!!
« Reply #32 on: November 20, 2016, 07:32:55 PM »
Thanks Mike!!
Logged

Offline TOTALLYRC

*
  • 861 861
Re: LOVING the PMC!! Thanks Steve!!!
« Reply #33 on: November 20, 2016, 07:51:03 PM »
No problem.
I am just spreading the PMC love!!!!
Logged
We never have the time or money to do it right the first time, but we somehow manage to do it twice and then spend the money to get it right.

Offline thespindoctor

*
  • 307 307
    • The Spin Doctor
Re: LOVING the PMC!! Thanks Steve!!!
« Reply #34 on: November 20, 2016, 08:21:41 PM »
I want to fall in love too! But when to use this is in Mach4. 
Is it just to deal with inputs and outputs monitoring activities or could it be used to write a probe routine for instance?

Thanks,
Keith
Logged

Offline TOTALLYRC

*
  • 861 861
Re: LOVING the PMC!! Thanks Steve!!!
« Reply #35 on: November 20, 2016, 08:48:46 PM »
While the PMC is very powerful I am not sure if you can do that with it.

Mike
Logged
We never have the time or money to do it right the first time, but we somehow manage to do it twice and then spend the money to get it right.

Offline arturod

*
  • 150 150
    • CNC4PC
Re: LOVING the PMC!! Thanks Steve!!!
« Reply #36 on: June 09, 2017, 08:58:26 AM »
Steve,

It looks like PMC is still not doing calculations with decimals:

Arturo Duncan
http://cnc4pc.com
Logged

Offline smurph

*
  • *
  • 1,574 1,574
  • "That there... that's an RV."
Re: LOVING the PMC!! Thanks Steve!!!
« Reply #37 on: June 09, 2017, 12:36:00 PM »
Arturo,

I need an example.  Because what I just tested works.  Can you post the PMC file? 

Steve
Logged

Offline arturod

*
  • 150 150
    • CNC4PC
Re: LOVING the PMC!! Thanks Steve!!!
« Reply #38 on: June 09, 2017, 01:01:37 PM »
Steve,

Here it is.

I had to add the .txt so it would allow to upload it.

Arturo Duncan
http://cnc4pc.com
Logged

Offline smurph

*
  • *
  • 1,574 1,574
  • "That there... that's an RV."
Re: LOVING the PMC!! Thanks Steve!!!
« Reply #39 on: June 09, 2017, 06:23:59 PM »
Ok Arturo, I think I have it.  Thanks for the example because the math portion was working correctly.  The error was with reading and writing registers.  The fix will be in the next build.  

Steve
Logged
Pages: « 1 2 3 4 5 »   Go Up
« previous next »