Author Topic: Murphy’s Law strikes again.  (Read 6475 times)

0 Members and 1 Guest are viewing this topic.

Offline Tweakie.CNC

  • Global Moderator
  • *
  • Posts: 7,641
  • Super Kitty
    • View Profile
    • Tweakie.CNC
Murphy’s Law strikes again.
« on: May 07, 2014, 06:22:03 AM »

You check the CAD/CAM layout 100 times, you check the engraved part, you screw it up – stand back to admire and bang the mistake is obvious.  :'(

Tweakie.



Success consists of going from failure to failure without loss of enthusiasm.  Winston Churchill.

Offline Ya-Nvr-No

  • Active Member
  • Posts: 971
    • View Profile
    • Ya-Nvr-No
Re: Murphy’s Law strikes again.
« Reply #1 on: May 07, 2014, 07:52:43 AM »
Have to assume you sawed through it? Cause I have no idea what it says.
Nice clean graphics work your providing.

Offline Tweakie.CNC

  • Global Moderator
  • *
  • Posts: 7,641
  • Super Kitty
    • View Profile
    • Tweakie.CNC
Re: Murphy’s Law strikes again.
« Reply #2 on: May 07, 2014, 09:13:22 AM »
Thanks Craig.  ;D

(Perhaps I should have taken the full picture - it's the annotation for my 'Weather Stone' and the black line is the string suspending the actual stone).

Tweakie.


addendum:  It gets worse - only since looking at it again here, I have noticed there is more than one mistake  ;D ;D
« Last Edit: May 07, 2014, 09:33:45 AM by Tweakie.CNC »
Success consists of going from failure to failure without loss of enthusiasm.  Winston Churchill.

Offline Overloaded

  • Global Moderator
  • *
  • Posts: 4,763
    • View Profile
Re: Murphy’s Law strikes again.
« Reply #3 on: May 07, 2014, 09:40:03 AM »
The suspense was killing me. I almost bit first ... THANKS Craig  ;D

It does look very nice Tweakie, was looking for a typo but am not familiar with that particular lingo. All looks spelt rite to me. ;)

Thanks,
Russ
 :)

Offline Overloaded

  • Global Moderator
  • *
  • Posts: 4,763
    • View Profile
Re: Murphy’s Law strikes again.
« Reply #4 on: May 07, 2014, 09:41:35 AM »
Slightly out of plumb ? ? or, is there a breeze ?
Russ

Offline Tweakie.CNC

  • Global Moderator
  • *
  • Posts: 7,641
  • Super Kitty
    • View Profile
    • Tweakie.CNC
Re: Murphy’s Law strikes again.
« Reply #5 on: May 07, 2014, 10:19:35 AM »
I make no excuses fellas - it was a holiday weekend, with friends around, and we all had a modicum of beers before we set about this project.

Yes Russ, out of plumb as well  ;D

Tweakie.
Success consists of going from failure to failure without loss of enthusiasm.  Winston Churchill.

Offline Picengraver

  • Active Member
  • Posts: 342
    • View Profile
Re: Murphy’s Law strikes again.
« Reply #6 on: May 07, 2014, 12:33:38 PM »
Tweakie,
I'm pretty sure I see the mistake(s), and the beers are certainly an acceptable excuse, but then I'll not be the one to spoil your party.   ;D
All the Best,
John Champlain

Offline Chaoticone

  • Administrator
  • *
  • Posts: 5,433
  • Precision Chaos
    • View Profile
Re: Murphy’s Law strikes again.
« Reply #7 on: May 07, 2014, 12:49:06 PM »
What beems to be the soblem Tweakie?

Brett
;D If you could see the things I have in my head, you would be laughing too. ;D

My guard dog is not what you need to worry about!

Offline Ya-Nvr-No

  • Active Member
  • Posts: 971
    • View Profile
    • Ya-Nvr-No
Re: Murphy’s Law strikes again.
« Reply #8 on: May 07, 2014, 12:57:21 PM »
So you plumbed it holding a long neck bottle?
hell... close enough then.

Offline Overloaded

  • Global Moderator
  • *
  • Posts: 4,763
    • View Profile
Re: Murphy’s Law strikes again.
« Reply #9 on: May 07, 2014, 12:59:25 PM »
Looks like the order might be unconventional ... or mismatched. ? ?

That little bit of pure English looks out of place as well. ? ?

Other than that, it looks gurty pood.

Russ