Hello Guest it is March 28, 2024, 11:38:58 AM

Author Topic: MR-J2S-A and Mach 3  (Read 21492 times)

0 Members and 1 Guest are viewing this topic.

Offline sdow

*
  •  67 67
    • View Profile
Re: MR-J2S-A and Mach 3
« Reply #40 on: November 05, 2013, 11:44:51 PM »
Hi Hood

When i put directly 3v to VC  ... my motor not run ? 

Offline Hood

*
  •  25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: MR-J2S-A and Mach 3
« Reply #41 on: November 06, 2013, 02:56:14 AM »
Do you have pins 15, 16 and 17 connected to pin 10?
Have you set the parameters in the drive for Speed mode?

Hood

Offline sdow

*
  •  67 67
    • View Profile
Re: MR-J2S-A and Mach 3
« Reply #42 on: November 06, 2013, 08:44:29 AM »
yes i connect 15  16 17 to 10   ...but not set the parameters  i can not find this   ?  But, when i connect pin 5 to 10 ...i have torque ?
« Last Edit: November 06, 2013, 08:47:13 AM by sdow »

Offline sdow

*
  •  67 67
    • View Profile
Re: MR-J2S-A and Mach 3
« Reply #43 on: November 06, 2013, 01:23:20 PM »
i put the parameter no.43 -> 0111   no.44 -> 0222 no.45-> 0665 no.46->0770 no.47->0883 no.48-> 0994

battery:  + to VC and - to LG

Offline Hood

*
  •  25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: MR-J2S-A and Mach 3
« Reply #44 on: November 06, 2013, 04:52:59 PM »
Do you have the software for the drive? I think that would make it easier to understand and set parameters. I had a quick look and the ones you mentioned above are the default settings so likely they will need changed to suit whichever mode you are in (Speed, Torque, Position)

Hood

Offline sdow

*
  •  67 67
    • View Profile
Re: MR-J2S-A and Mach 3
« Reply #45 on: November 06, 2013, 04:55:17 PM »
yes

Offline Hood

*
  •  25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: MR-J2S-A and Mach 3
« Reply #46 on: November 06, 2013, 04:58:03 PM »
So have you connected the drives up to the software/
Hood

Offline sdow

*
  •  67 67
    • View Profile
Re: MR-J2S-A and Mach 3
« Reply #47 on: November 06, 2013, 05:00:41 PM »
i use the page  :  3-6   and  5-2 to 5-3

Offline sdow

*
  •  67 67
    • View Profile
Re: MR-J2S-A and Mach 3
« Reply #48 on: November 06, 2013, 05:01:51 PM »
yes i can run the motor with software in Test -> JOG

Offline sdow

*
  •  67 67
    • View Profile
Re: MR-J2S-A and Mach 3
« Reply #49 on: November 06, 2013, 05:04:55 PM »
if you look in parameter n0.43 to 48    i set it in default .