Hello
Guest
it is
March 28, 2024, 09:35:48 AM
Guest
Login
Register
Menu
Home
Help
Search
Calendar
Members
Members
View the memberlist
Search For Members
Login
Register
YouTube
Machsupport Forum
/
Mach Discussion
/
General Mach Discussion
/
Need Help , Have Questions
« previous
next »
Print
Pages:
«
1
2
3
4
»
Go Down
Author
Topic: Need Help , Have Questions (Read 15708 times)
0 Members and 1 Guest are viewing this topic.
Satbeam
33
Re: Need Help , Have Questions
«
Reply #20 on:
August 31, 2008, 03:06:52 PM »
I do not realy know what that is or where I find them . Or is it the diamitor of the shaft = 1/4 shaft , motor settings 200 = 720 = 287.5 Step pulse 0 and Dir Pulse 0 .
Logged
Hood
25,835
Carnoustie, Scotland
Re: Need Help , Have Questions
«
Reply #21 on:
August 31, 2008, 05:06:57 PM »
You say you have the stepper drives from Probotix so looking at the manual there on page 1 is a diagram showing the dip switches, see what they are set to and read from the table. 1/8 step will probably be the best for you but whether they are at that I dont know.
Hood
Logged
Satbeam
33
Re: Need Help , Have Questions
«
Reply #22 on:
August 31, 2008, 05:45:05 PM »
Send me the page , I can't find it .
Logged
Hood
25,835
Carnoustie, Scotland
Re: Need Help , Have Questions
«
Reply #23 on:
August 31, 2008, 05:49:48 PM »
Heres the manual for one of their drives
http://www.probotix.com/manuals/ProboStepVX.pdf
Is that the one you have?
Hood
Logged
Satbeam
33
Re: Need Help , Have Questions
«
Reply #24 on:
August 31, 2008, 06:30:03 PM »
Unfourtionitley that is not it . The board I have they do not make or sell anymore . Mine has lights yellow -red & green with no dip switches . This is the highest volts or amps . The only think is to write Probotix , I will do that if you its need . Or is their another avanue we can go ?
Logged
Hood
25,835
Carnoustie, Scotland
Re: Need Help , Have Questions
«
Reply #25 on:
August 31, 2008, 06:35:00 PM »
OK you can do it by trial and error, enter 4000 in steps per unit for the X axis and save, then go to the MDI page and type G0X1 and see if the axis moves 1 inch, if not roughly measure how far it moves and we can go from there.
Hood
Logged
Satbeam
33
Re: Need Help , Have Questions
«
Reply #26 on:
August 31, 2008, 06:54:09 PM »
Sorry I do not know where to tip on the MDI page .
Logged
Hood
25,835
Carnoustie, Scotland
Re: Need Help , Have Questions
«
Reply #27 on:
August 31, 2008, 06:59:04 PM »
Click on the window as shown in the screenshot, type in G0X1 like in the screenshot and then press your keyboards Enter key
Hood
Logged
Satbeam
33
Re: Need Help , Have Questions
«
Reply #28 on:
August 31, 2008, 07:14:02 PM »
It went almost 1/4 " and very slow .
Logged
Hood
25,835
Carnoustie, Scotland
Re: Need Help , Have Questions
«
Reply #29 on:
August 31, 2008, 07:17:44 PM »
OK so try 16,000 now for x axis steps per unit then repeat the MDI but remember to zero the X axis first.
Hood
Logged
Print
Pages:
«
1
2
3
4
»
Go Up
« previous
next »