Hello Guest it is November 17, 2019, 09:16:58 PM
Profile Guest
« previous next »
Pages: 1   Go Down

Author Topic: WinCNC and Mach3 compatability  (Read 4005 times)

0 Members and 1 Guest are viewing this topic.

Offline Fabcan

*
  • 2 2
    • View Profile
WinCNC and Mach3 compatability
« on: March 27, 2006, 03:50:28 PM »
Hello everyone,I purchased a PracticalCNC machine with WinCNC and was wandering if Mach3 is compatable with it.Also,any information on any other programs that might be helpfull would be appreciated.Thanks in advance for any and al help.
Logged

Offline efrem

*
  • 12 12
    • View Profile
Re: WinCNC and Mach3 compatability
« Reply #1 on: April 01, 2006, 05:37:31 PM »
I'm not sure but I think that they aren't compatible just because mach3 doesn't support PCI I/O cards and works with the parallel port ...
Logged

Offline Brian Barker

*
  • *
  • 3,518 3,518
    • View Profile
Re: WinCNC and Mach3 compatability
« Reply #2 on: April 02, 2006, 05:40:54 PM »
WinCNC is doing the same job as Mach3 ... The old Ford Chevy thing...
Logged
Fixing problems one post at a time ;)

www.newfangledsolutions.com
www.machsupport.com

Offline Fabcan

*
  • 2 2
    • View Profile
Re: WinCNC and Mach3 compatability
« Reply #3 on: April 02, 2006, 07:16:04 PM »
thanks again for the input
Logged

Offline 7steps2CNC

*
  • 2 2
  • 7 Easy Steps to CNC Programming
    • View Profile
    • Haydenpub.com
Re: WinCNC and Mach3 compatability
« Reply #4 on: April 09, 2006, 09:03:29 AM »
I guess I am a little slow on the uptake here.  Are we saying, winCNC and MAch 3 are not compatable like you would not pug a Chevy starter on a Ford Engine. . . or are we saying picking one is a matter of preference and either with work.  I would really like to help a friend relplace his wincnc system
Logged
Publisher of
7 Easy Steps to CNC Programming . . . A Beginner's Guide
7 Easy Steps to CNC Programming, Book II, Beyond the Beginning
7 Easy Steps to BobCAD/CAM . . .A Beginner's Guide

Offline Brian Barker

*
  • *
  • 3,518 3,518
    • View Profile
Re: WinCNC and Mach3 compatability
« Reply #5 on: April 09, 2006, 09:08:14 AM »
It is a matter of preference...  :)
Logged
Fixing problems one post at a time ;)

www.newfangledsolutions.com
www.machsupport.com

Offline 7steps2CNC

*
  • 2 2
  • 7 Easy Steps to CNC Programming
    • View Profile
    • Haydenpub.com
Re: WinCNC and Mach3 compatability
« Reply #6 on: April 09, 2006, 09:28:51 AM »
Cool. Is there any information floating around about how to make the conversion?
Logged
Publisher of
7 Easy Steps to CNC Programming . . . A Beginner's Guide
7 Easy Steps to CNC Programming, Book II, Beyond the Beginning
7 Easy Steps to BobCAD/CAM . . .A Beginner's Guide

Offline Brian Barker

*
  • *
  • 3,518 3,518
    • View Profile
Re: WinCNC and Mach3 compatability
« Reply #7 on: April 09, 2006, 09:45:46 AM »
Do you have a pin out for there cables or any other info? If you do I can take a quick look at it...
Logged
Fixing problems one post at a time ;)

www.newfangledsolutions.com
www.machsupport.com
Pages: 1   Go Up
« previous next »