Hello Guest it is July 01, 2025, 05:37:47 AM
Profile Guest
« previous next »
Pages: « 1 2   Go Down

Author Topic: Mach3 stops approx every 10 min. / 10,000 lines of code  (Read 31931 times)

0 Members and 2 Guests are viewing this topic.

Offline ger21

*
  • *
  • 6,295 6,295
    • The CNC Woodworker
Re: Mach3 stops approx every 10 min. / 10,000 lines of code
« Reply #10 on: May 28, 2018, 09:13:21 PM »
Quote from: rbullard on May 28, 2018, 01:03:19 PM
Quote from: ger21 on May 27, 2018, 04:29:39 PM
Is there any type of message when it stops?
No - The only message next to reset is just "Press Reset...Emergency Mode Active" ... No error codes

So the reset button is flashing when it stops?
Sounds like you have noise triggering your estop input, or possibly a limit input?
Logged
Gerry

2010 Screenset
http://www.thecncwoodworker.com/2010.html

JointCAM Dovetail and Box Joint software
http://www.g-forcecnc.com/jointcam.html

Offline joeaverage

*
  • 7,604 7,604
Re: Mach3 stops approx every 10 min. / 10,000 lines of code
« Reply #11 on: May 29, 2018, 12:37:57 AM »
Hi,
is it possible that there is an overheat alarm which causes the Estop?

Would explain the approximate consistent fault AND the Estop.

Craig
Logged
'I enjoy sex at 73.....I live at 71 so its not too far to walk.'

Offline ger21

*
  • *
  • 6,295 6,295
    • The CNC Woodworker
Re: Mach3 stops approx every 10 min. / 10,000 lines of code
« Reply #12 on: May 29, 2018, 07:50:07 AM »
If it was overheating, I doubt that he would be able to continue running after it stops?

Or if it did, I'd expect it to stop much sooner the next time?
Logged
Gerry

2010 Screenset
http://www.thecncwoodworker.com/2010.html

JointCAM Dovetail and Box Joint software
http://www.g-forcecnc.com/jointcam.html

Offline RICH

*
  • *
  • 7,427 7,427
Re: Mach3 stops approx every 10 min. / 10,000 lines of code
« Reply #13 on: May 29, 2018, 05:17:52 PM »
Only the Chinese know how their thermal overload  works. suggest the user jumper it out and test.
Have a look at the schematic.

RICH
Logged

Offline Pythagoras

*
  • 93 93
  • a² + b² = c²
Re: Mach3 stops approx every 10 min. / 10,000 lines of code
« Reply #14 on: June 03, 2018, 08:27:23 AM »
My 2 cents, noise on the Estop.
Also are you running the same gcode, and is it stopping at the same point in that code?
Logged
The Pythagorean theorem: The sum of the areas of the two squares on the legs (a and b) equals the area of the square on the hypotenuse (c).     a² + b² = c².

Offline Mpace100

*
  • 1 1
Re: Mach3 stops approx every 10 min. / 10,000 lines of code
« Reply #15 on: February 16, 2020, 10:22:23 PM »
Any luck with this? I am having exactly the same issue. I have tried on different PCs with the he same result.

Thanks Marvin
Logged

Offline GabeR

*
  • 2 2
Re: Mach3 stops approx every 10 min. / 10,000 lines of code
« Reply #16 on: April 08, 2021, 12:56:48 PM »
Have the same issue. every 10 minuts stops without errors, anybody figure it out?
Logged
Pages: « 1 2   Go Up
« previous next »