Hello Guest it is December 01, 2020, 06:07:09 AM

Author Topic: Mach 3 only loads half of the gcode  (Read 15065 times)

0 Members and 1 Guest are viewing this topic.

Re: Mach 3 only loads half of the gcode
« Reply #10 on: November 16, 2016, 09:39:25 AM »
I to have the same problem with my system. It only cut 500 lines even though it is licensed, I bought the license from the mach3 website. It comes up as licensed with my name
but still only 500 lines. I can disable the port and it sets all lines but won't cut any thing. Enable and it runs as demo but it is licensed.

Offline rcaffin

*
  •  1,034 1,034
    • View Profile
Re: Mach 3 only loads half of the gcode
« Reply #11 on: December 03, 2016, 10:53:24 PM »
This is a licencing issue. Contact Artsoft.
Cheers
Roger

Offline Tweakie.CNC

*
  • *
  •  8,561 8,561
  • Super Kitty
    • View Profile
    • Tweakie.CNC
Re: Mach 3 only loads half of the gcode
« Reply #12 on: December 04, 2016, 01:34:11 AM »
This .pdf gives an explanation regarding license installation;  ftp://anonymous:guest@ftp.machsupport.com/Extra%20Information/Mach3%20License%20install%201.pdf

Tweakie.
KEEP SAFE !

Offline rcaffin

*
  •  1,034 1,034
    • View Profile
Re: Mach 3 only loads half of the gcode
« Reply #13 on: December 04, 2016, 01:48:03 AM »
Hey Tweakie - that URL does not work for me.
Cheers
Roger

Offline Tweakie.CNC

*
  • *
  •  8,561 8,561
  • Super Kitty
    • View Profile
    • Tweakie.CNC
Re: Mach 3 only loads half of the gcode
« Reply #14 on: December 04, 2016, 03:41:27 AM »
Hi Roger,

I was in two minds about posting it as ftp:// links work for some and not for others.  :'(

(You can get the .pdf by going to the .ftp downloads area http://www.machsupport.com/software/downloads-updates/ , it is listed under Extra Information).

Tweakie.
KEEP SAFE !

Offline rcaffin

*
  •  1,034 1,034
    • View Profile
Re: Mach 3 only loads half of the gcode
« Reply #15 on: December 04, 2016, 03:53:28 AM »
The wheels sit there spinning, and spinning ...
But they never get there???
WXP SP3

Cheers
Roger

Offline Tweakie.CNC

*
  • *
  •  8,561 8,561
  • Super Kitty
    • View Profile
    • Tweakie.CNC
Re: Mach 3 only loads half of the gcode
« Reply #16 on: December 06, 2016, 03:54:27 AM »
The wheels sit there spinning, and spinning ...
But they never get there???
WXP SP3

Cheers
Roger


You could perhaps try resetting your DNS Server.

Tweakie.
KEEP SAFE !

Offline rcaffin

*
  •  1,034 1,034
    • View Profile
Re: Mach 3 only loads half of the gcode
« Reply #17 on: December 06, 2016, 04:29:37 AM »
My system must be locking out whatever response the FTP side of things is getting. No idea why.
Maybe an adblocker and a cookie filter?
Cheers
Roger