Hello Guest it is May 07, 2021, 08:40:58 AM

Author Topic: Motors not responding  (Read 9845 times)

0 Members and 1 Guest are viewing this topic.

Re: Motors not responding
« Reply #20 on: November 23, 2011, 12:00:25 PM »
Hello Tweakie, I agree,it will probably be something simple that is wrong.  I did not swap the hard drive on the pc's.

John

Offline Tweakie.CNC

*
  • *
  •  8,705 8,705
  • Super Kitty
    • View Profile
    • Tweakie.CNC
Re: Motors not responding
« Reply #21 on: November 23, 2011, 12:16:19 PM »
How about using a spare axis - "A" for example (on the side of the PCB) and then set up your Mach ports and pins configuration to drive this axis as though it is the X Axis. ??

Tweakie.
KEEP SAFE !
Re: Motors not responding
« Reply #22 on: November 23, 2011, 01:32:39 PM »
Hello Tweakie, Without the driver installed ,nothing responds.

John
Re: Motors not responding
« Reply #23 on: November 23, 2011, 09:03:02 PM »
Hello Tweakie,  Thank you very much for the link you sent for the Mach optimization txt. .  It worked excellent. I have everything up and running.I don't know exactly what part of the optimization made it work because I only did the following steps.6,7,11,12,16,20,21,22,23.Once again,thank you and I thank everyone for their help.

John

Offline Tweakie.CNC

*
  • *
  •  8,705 8,705
  • Super Kitty
    • View Profile
    • Tweakie.CNC
Re: Motors not responding
« Reply #24 on: November 24, 2011, 02:10:31 AM »
Excellent news John, I am really pleased you have got it running.  :D

Tweakie.
KEEP SAFE !
Re: Motors not responding
« Reply #25 on: November 24, 2011, 12:45:40 PM »
Hello Tweakie, Thanks again . The reason I posted the steps that I took was for anyone who might have the same problem.Mach3 should run on any Pc if they follow the steps listed. I tried it on 3 Pc's that wouldn't run Mach3 before and now they can run it.
  I wish everyone a Happy Thanksgiving.

John
Re: Motors not responding
« Reply #26 on: November 29, 2011, 02:42:33 PM »
According to your Mach3.xml PulseWidth is 0 (zero). It must be 1 to 15 microsecond. Config/Motor Tunning! Don't check DirLowActive in Motor Outputs. Must be red.
Regards!
Rudolf
Re: Motors not responding
« Reply #27 on: November 14, 2013, 07:28:56 PM »
need machx lisence and paperwork/instructions   help

Offline Tweakie.CNC

*
  • *
  •  8,705 8,705
  • Super Kitty
    • View Profile
    • Tweakie.CNC
Re: Motors not responding
« Reply #28 on: November 15, 2013, 01:59:44 AM »
Quote
need machx lisence and paperwork/instructions   help

http://www.machsupport.com/help-learning/product-manuals/

http://www.machsupport.com/licensing/

Tweakie.
KEEP SAFE !
Re: Motors not responding
« Reply #29 on: November 20, 2013, 03:17:40 PM »
Hi Tweekie, I have the same problem as John05 and not you sent him his reply was.
Hello Tweakie,  Thank you very much for the link you sent for the Mach optimization txt. .  It worked excellent. I have everything up and running.I don't know exactly what part of the optimization made it work because I only did the following steps.6,7,11,12,16,20,21,22,23.Once again,thank you and I thank everyone for their help.

John
Is it possible to send me the same link to see if it sorts out my problem with the motors not responding, I to have had to change my PC and the new one runs Windows 7 the old system ran XP for several years without any problems