Hello Guest it is August 18, 2019, 07:43:59 AM

Author Topic: Mach to DeskCNC?  (Read 16207 times)

0 Members and 1 Guest are viewing this topic.

Re: Mach to DeskCNC?
« Reply #10 on: November 09, 2006, 02:01:32 PM »
The same old thing Firmware ;(
Fixing problems one post at a time ;)

www.newfangledsolutions.com
www.machsupport.com

Offline Greolt

*
  •  956 956
    • View Profile
Re: Mach to DeskCNC?
« Reply #11 on: November 23, 2006, 02:50:15 AM »
I have no wish to be a pest  ::)

But any progress on this?
Re: Mach to DeskCNC?
« Reply #12 on: November 24, 2006, 01:35:41 PM »
You are not a pest, it is good that you would like to know this!

Yes it is moving motors and seems to be working smooth at this time! There is still a bit of a firmware problem should be fixed in a week or so.

Thanks
Brian
Fixing problems one post at a time ;)

www.newfangledsolutions.com
www.machsupport.com

Offline Greolt

*
  •  956 956
    • View Profile
Re: Mach to DeskCNC?
« Reply #13 on: December 03, 2006, 01:09:36 AM »
I see on the Yahoo group that Art has posted asking for user response to the ncPod.

Nothing mentioned on this forum :(

Guess I'll have to join the Yahoo group  ;D

ynneb

*
Re: Mach to DeskCNC?
« Reply #14 on: December 03, 2006, 02:56:13 AM »
I see on the Yahoo group that Art has posted asking for user response to the ncPod.

Nothing mentioned on this forum :(

Guess I'll have to join the Yahoo group  ;D

Sorry Greg, you are not getting value for money here :)

Offline Greolt

*
  •  956 956
    • View Profile
Re: Mach to DeskCNC?
« Reply #15 on: December 03, 2006, 03:34:04 AM »
 ;D ;D ;D ;D ;D ;D ;D ;D ;D

No, there are a lot of helpful people here.  And they are much appreciated.

I have learned quite a bit just reading others questions and the assistance given.

However I saw a flurry of discussion on the Yahoo group about the ncPod and was surprised to see
not a mention on here.

Re: Mach to DeskCNC?
« Reply #16 on: December 03, 2006, 06:22:56 PM »
The NC pod is about done and I should have mine set up for testing very soon :)
Fixing problems one post at a time ;)

www.newfangledsolutions.com
www.machsupport.com

Offline Greolt

*
  •  956 956
    • View Profile
Re: Mach to DeskCNC?
« Reply #17 on: December 03, 2006, 10:23:53 PM »
 ;D ;D I seem to have an unfortunate habit of not putting things very well. ;D ;D

I was not meaning to complain that this thread shoud have been updated :D

Just was searching for posts talking about the nPod after seeing so many on the Yahoo group.

Really appreciate all the support you and others do on this forum Brian :)

Can you tell I am exited about the prospect of the ncPod coming on line?   ;D ;D

Offline Greolt

*
  •  956 956
    • View Profile
Re: Mach to DeskCNC?
« Reply #18 on: December 05, 2006, 07:19:37 PM »
Some one asked on CNCzone where to find a pic of the ncPod.

Maybe others are curious   :)

« Last Edit: December 05, 2006, 07:22:00 PM by Greolt »

Offline PaulWC

*
  •  125 125
    • View Profile
Re: Mach to DeskCNC?
« Reply #19 on: December 05, 2006, 10:03:45 PM »
Hi Brian,

Is the ncPod capable/scheduled to take threading encoder input?

I take it the pictured board transplants the DeskCNC board? Mine has the encoder pluged into it.

Thanks, Paul, Central OR