Good morning
I put these two scripts in a me error button, individually they work
someone can kindly correct
I admit my complete ignorance in VB!
thank you
Sub Main
Begin Dialog SelectCentering 350,145,230,150,"SELEZIONA CENTRO"
OKButton 70,120,40,14
CancelButton 120,120,40,14
GroupBox 30,5,170,100,"CENTRATURA",.GroupBox1
OptionGroup .OptionGroup1
OptionButton 46,24,150,8," CENTRO PEZZO PIENO",.OptionButton1
OptionButton 46,40,150,8," CENTRO PEZZO INTERNO" ,.OptionButton2
End Dialog
Dim Dlg1 As SelectCentering
Button = Dialog (Dlg1)
If Button = 0 Then Exit Sub
Selected = Dlg1.OptionGroup1
'CENTRO pezzo pieno is selected ***************************************************
If Selected = 0 Then '********************************************
Rem VBScript To center probe outside diameter Metric Version
Speak (" psizionarsi CINQUE millimetri sopra il pezzo") 'Avviso Vocale
response = MsgBox (" 5 mm SOPRA IL PEZZO")
Sleep (1000) ' pausa di 1 secondi
Speak (" CONFERMARE centro pezzo pieno") 'Avviso Vocale
Message "INIZIO CENTRO PEZZO PIENO"
Sleep (1000) ' pausa di 1 secondi
response = MsgBox ("CONFERMARE CENTRO PEZZO PIENO")
CurrentFeed = GetOemDRO(818) 'Get the current feedrate to return to later
CurrentAbsInc = GetOemLED(48) 'Get the current G90/G91 state
CurrentGmode = GetOemDRO(819) 'Get the current G0/G1 state
CurrentToolDiameter = GetOemDRO(1000) 'gets the current tool diameter
If GetOemLed (825) <> 0 Then 'Check to see if the probe is already grounded or faulty
Call ProbeGrounded()
Exit Sub
Else
XCurrent = GetDro(0)
YCurrent = GetDro(1)
OutsideDiameter = GetUserDRO(1152)
Code "G4 P1" 'Pause 1 second to give time to position probe plate
While IsMoving ()
Wend
Call SetDro (0,0.000)
While IsMoving ()
Wend
Call SetDro (1,0.000)
Code "F50" 'slow feed rate to 100mm/sec
Code "G90 G0 X" &XNew + OutsideDiameter * .6
Code "G91 G0 Z-10"
Rem Probe Left
XNew = Xcurrent - OutsideDiameter * .6
Code "G31 X" &XNew
While IsMoving() 'wait for the move to finish
Wend
XPos1 = GetVar(2000) 'get the probe touch location
Code "G91 G0 X2"
Code "G91 G0 Z10"
Code "G90 G0 X" &XCurrent 'rapid move back to start point
Code "G91 G0 X" &XCurrent - OutsideDiameter * .6
Code "G91 G0 Z-10"
Rem Probe Right
XNew = XCurrent + 75 'probe 75mm to right
Code "G31 X" &XNew
While IsMoving()
Wend
XPos2 = GetVar(2000)
Code "G91 G0 X-2"
Code "G91 G0 Z10"
XCenter = (XPos1 + XPos2) / 2 'center is midway between XPos1 and XPos2
Code "G90 G0 X" &XCenter 'rapid move to the x center location
While IsMoving ()
Wend
Call SetDro (0,0.000)
Code "G4 P0.25"
Code "G90 G0 Y" &YNew - OutsideDiameter * .6
Code "G91 G0 Z-10"
Rem Probe up
YNew = YCurrent + 75
Code "G31 Y" &YNew
While IsMoving()
Wend
YPos1 = GetVar(2001)
Code "G91 G0 Y-2"
Code "G91 G0 Z10"
Code "G90 G0 Y" &YCurrent
Code "G91 G0 Y" &YCurrent + OutsideDiameter * .6
Code "G91 G0 Z-10"
Rem Probe down
YNew = YCurrent - 75
Code "G31 Y" &YNew
While IsMoving()
Wend
YPos2 = GetVar(2001)
Code "G91 G0 Y2"
Code "G91 G0 Z10"
YCenter = (YPos1 + YPos2) / 2
Rem move To the center
Code "G90 G0 Y" &YCenter
While IsMoving ()
Wend
Call SetDro (1,0.000)
While IsMoving ()
Wend
Call SetUserDro (1152,YPos2 - YPos1 - CurrentToolDiameter)
Code "G4 P0.25"
Code "F" &CurrentFeed 'restore starting feed rate
Call ReturnG90G91State()
Exit Sub
End If
Sub ProbeGrounded()
Code "(Probe plate is grounded, check connection and try again)"
Call ReturnG90G91State()
End Sub
Sub ReturnG90G91State()
If CurrentAbsInc = 0 Then 'if G91 was in effect before then return to it
Code "G91"
End If
If CurrentGMode = 0 Then 'if G0 was in effect before then return to it
Code "G0"
End If
End Sub
End If '*********************************************************
'CENTRO PEZZO INTERNO is selected **************************************************
If Selected = 1 Then '*******************************************
Speak ("ricerca centro pezzointerno") 'Avviso Vocale
Message "RICERCA CENTRO PEZZO INTERNO"
Sleep (1000) ' pausa di 1 secondi
response = MsgBox ("CONFERMARE RICERCA CENTRO PEZZO INTERNO")
Sleep (1000) ' pausa di 1 secondi
Speak (" CONFERMARE centro pezzo interno") 'Avviso Vocale
Message "INIZIO CENTRO PEZZO INTERNO"
Sleep (1000) ' pausa di 1 secondi
response = MsgBox ("CONFERMARE CENTRO PEZZO INTERNO")
Call SetDRO(0,0)
Call SetDRO(1,0)
Xpos = GetParam("XDRO")
Ypos = GetParam("YDRO")
Fcurr = GetParam("FeedRate")
SP = 80 ' avanzamento prima palp impostare diametro mm del cerchio da palpare
VSP = "F200" ' velocita avanzamento prima palp
bkSP = 3 ' ritorno dopo palp mm
VbkSP = "F240" ' velocita ritorno
Spp = 5 ' avanzamento seconda palp mm
VSpp = "F40" ' velocita seconda palp
Code "G31 X" & (GetParam("XDRO")+SP) & (VSP)
While IsMoving()
Wend
Code "G0 X" & (GetParam("XDRO")-bkSP) & (VbkSP)
While IsMoving()
Wend
Code "G31 X" & (GetParam("XDRO")+Spp) & VSpp
While IsMoving()
Wend
B=GetParam("XDRO")
Code "G0 X" & Xpos
Code "G31 X" & (GetParam("XDRO")-SP) & (VSP)
While IsMoving()
Wend
Code "G0 X" & (GetParam("XDRO")+bkSP) & (VbkSP)
While IsMoving()
Wend
Code "G31 X" & (GetParam("XDRO")-Spp) & VSpp
While IsMoving()
Wend
A=GetParam("XDRO")
measuredX = B-A
Code "G0 X" & (A+(B-A)/2)
While IsMoving()
Wend
Code "G31 Y" & (GetParam("YDRO")+SP) & (VSP)
While IsMoving()
Wend
Code "G0 Y" & (GetParam("YDRO")-bkSP) & (VbkSP)
While IsMoving()
Wend
Code "G31 Y" & (GetParam("YDRO")+Spp) & VSpp
While IsMoving()
Wend
B=GetParam("YDRO")
Code "G0 Y" & Ypos
Code "G31 Y" & (GetParam("YDRO")-SP) & (VSP)
While IsMoving()
Wend
Code "G0 Y" & (GetParam("YDRO")+bkSP) & (VbkSP)
While IsMoving()
Wend
Code "G31 Y" & (GetParam("YDRO")-Spp) & VSpp
While IsMoving()
Wend
A=GetParam("YDRO")
measuredY = B-A
SetOEMDro(1152,measuredY + GetOEMDro(1000))
Code "G0 Y" & (A+(B-A)/2)
SetParam("FeedRate",Fcurr)
MsgBox (" Measurement X: " & nFmt(measuredX,3) & " mm Measurement Y: " & nFmt(measuredY,3) & " mm")
End If '*********************************************************
End Sub '**********************************************************