406/5000
good evening
I have this macro (not my found on the internet) "centerpiece full" and 'can modify it? I try to explain myself:
1 position me in the middle (approximate)
2 launch the macro, go x +
3 comes down and comes back to touch
4 gets up
and 'here' that I would like to change it, before it rises I would like it to come back a few mm, and if it could double-fingered.
thanks for any help
Rem VBScript To center probe outside diameter Metric Version
Speak (" psizionarsi CINQUE millimetri sopra il pezzo") 'Avviso Vocale
response = MsgBox (" 5 mm SOPRA IL PEZZO")
Sleep (1000) ' pausa di 1 secondi
Speak (" CONFERMARE centro pezzo pieno") 'Avviso Vocale
Message "INIZIO CENTRO PEZZO PIENO"
Sleep (1000) ' pausa di 1 secondi
response = MsgBox ("CONFERMARE CENTRO PEZZO PIENO")
CurrentFeed = GetOemDRO(818) 'Get the current feedrate to return to later
CurrentAbsInc = GetOemLED(48) 'Get the current G90/G91 state
CurrentGmode = GetOemDRO(819) 'Get the current G0/G1 state
CurrentToolDiameter = GetOemDRO(43) 'gets the current tool diameter
If GetOemLed (825) <> 0 Then 'Check to see if the probe is already grounded or faulty
Call ProbeGrounded()
Exit Sub
Else
XCurrent = GetDro(0)
YCurrent = GetDro(1)
OutsideDiameter = GetUserDRO(1152)
Code "G4 P1" 'Pause 1 second to give time to position probe plate
While IsMoving ()
Wend
Call SetDro (0,0.000)
While IsMoving ()
Wend
Call SetDro (1,0.000)
Code "F50" 'slow feed rate to 100mm/sec
Code "G90 G0 X" &XNew + OutsideDiameter * .6
Code "G91 G0 Z-10"
Rem Probe Left
XNew = Xcurrent - OutsideDiameter * .6
Code "G31 X" &XNew
While IsMoving() 'wait for the move to finish
Wend
XPos1 = GetVar(2000) 'get the probe touch location
Code "G91 G0 Z10"
Code "G90 G0 X" &XCurrent 'rapid move back to start point
Code "G91 G0 X" &XCurrent - OutsideDiameter * .6
Code "G91 G0 Z-10"
Rem Probe Right
XNew = XCurrent + 75 'probe 75mm to right
Code "G31 X" &XNew
While IsMoving()
Wend
XPos2 = GetVar(2000)
Code "G91 G0 Z10"
XCenter = (XPos1 + XPos2) / 2 'center is midway between XPos1 and XPos2
Code "G90 G0 X" &XCenter 'rapid move to the x center location
While IsMoving ()
Wend
Call SetDro (0,0.000)
Code "G4 P0.25"
Code "G90 G0 Y" &YNew - OutsideDiameter * .6
Code "G91 G0 Z-10"
Rem Probe up
YNew = YCurrent + 75
Code "G31 Y" &YNew
While IsMoving()
Wend
YPos1 = GetVar(2001)
Code "G91 G0 Z10"
Code "G90 G0 Y" &YCurrent
Code "G91 G0 Y" &YCurrent + OutsideDiameter * .6
Code "G91 G0 Z-10"
Rem Probe down
YNew = YCurrent - 75
Code "G31 Y" &YNew
While IsMoving()
Wend
YPos2 = GetVar(2001)
Code "G91 G0 Z10"
YCenter = (YPos1 + YPos2) / 2
Rem move To the center
Code "G90 G0 Y" &YCenter
While IsMoving ()
Wend
Call SetDro (1,0.000)
While IsMoving ()
Wend
Call SetUserDro (1152,YPos2 - YPos1 - CurrentToolDiameter)
Code "G4 P0.25"
Code "F" &CurrentFeed 'restore starting feed rate
Call ReturnG90G91State()
Exit Sub
End If
Sub ProbeGrounded()
Code "(Probe plate is grounded, check connection and try again)"
Call ReturnG90G91State()
End Sub
Sub ReturnG90G91State()
If CurrentAbsInc = 0 Then 'if G91 was in effect before then return to it
Code "G91"
End If
If CurrentGMode = 0 Then 'if G0 was in effect before then return to it
Code "G0"
End If
End Sub