Hello Guest it is October 22, 2019, 08:18:19 AM

Author Topic: Simulation  (Read 2392 times)

0 Members and 1 Guest are viewing this topic.

Simulation
« on: February 04, 2007, 04:10:28 PM »
I'm a newbe......I loaded Quantum on a computer to learn on. It is connected to only a printer. From my cad/cam I made 2 diameters at xyz zero. The area in between to be milled out with a .25 dia cutter to a -.400. The posted program is saved on a floppy at another computer and loaded on this one. To edit comes up within notebook as shown below.
%
O0010
N10G00G17G40G80G98G91G20
N20G00
N30T00M06
N40G00X0.0Y0.0S100M03
N50G01Y-0.4Z-0.1F10.
N60G02X-1.326Y-1.326I-1.326J0.0
N70X-1.326Y1.326I0.0J1.326
N80X1.326Y1.326I1.326J0.0
N90X1.326Y-1.326I0.0J-1.326
N100G00Z0.1
N110X0.348Y-0.4
N120G01Y0.4Z-0.1
N130G03X-1.674Y1.674I-1.674J0.0
N140X-1.674Y-1.674I0.0J-1.674
N150X1.674Y-1.674I1.674J0.0
N160X1.674Y1.674I0.0J1.674
N170G00Z0.1
N180X0.152Y0.3
N190G01X-0.4Z-0.1
N200G03X-0.3Y-0.3I0.0J-0.3
N210G02X-1.126Y-1.126I-1.126J0.0
N220X-1.126Y1.126I0.0J1.126
N230X1.126Y1.126I1.126J0.0
N240X1.126Y-1.126I0.0J-1.126
N250G03X0.3Y-0.3I0.3J0.0
N260G00Z0.1
N270X-0.252
N280G01X0.4Z-0.1
N290G03X0.3Y0.3I0.0J0.3
N300X-1.874Y1.874I-1.874J0.0
N310X-1.874Y-1.874I0.0J-1.874
N320X1.874Y-1.874I1.874J0.0
N330X1.874Y1.874I0.0J1.874
N340X-0.3Y0.3I-0.3J0.0
N350G00Z0.1
N360X-0.248Y0.1
N370G01Y-0.4Z-0.2
N380G02X-1.326Y-1.326I-1.326J0.0
N390X-1.326Y1.326I0.0J1.326
N400X1.326Y1.326I1.326J0.0
N410X1.326Y-1.326I0.0J-1.326
N420G00Z0.2
N430X0.348Y-0.4
N440G01Y0.4Z-0.2
N450G03X-1.674Y1.674I-1.674J0.0
N460X-1.674Y-1.674I0.0J-1.674
N470X1.674Y-1.674I1.674J0.0
N480X1.674Y1.674I0.0J1.674
N490G00Z0.2
N500X0.152Y0.3
N510G01X-0.4Z-0.2
N520G03X-0.3Y-0.3I0.0J-0.3
N530G02X-1.126Y-1.126I-1.126J0.0
N540X-1.126Y1.126I0.0J1.126
N550X1.126Y1.126I1.126J0.0
N560X1.126Y-1.126I0.0J-1.126
N570G03X0.3Y-0.3I0.3J0.0
N580G00Z0.2
N590X-0.252
N600G01X0.4Z-0.2
N610G03X0.3Y0.3I0.0J0.3
N620X-1.874Y1.874I-1.874J0.0
N630X-1.874Y-1.874I0.0J-1.874
N640X1.874Y-1.874I1.874J0.0
N650X1.874Y1.874I0.0J1.874
N660X-0.3Y0.3I-0.3J0.0
N670G00Z0.2
N680X-0.248Y0.1
N690G01Y-0.4Z-0.3
N700G02X-1.326Y-1.326I-1.326J0.0
N710X-1.326Y1.326I0.0J1.326
N720X1.326Y1.326I1.326J0.0
N730X1.326Y-1.326I0.0J-1.326
N740G00Z0.3
N750X0.348Y-0.4
N760G01Y0.4Z-0.3
N770G03X-1.674Y1.674I-1.674J0.0
N780X-1.674Y-1.674I0.0J-1.674
N790X1.674Y-1.674I1.674J0.0
N800X1.674Y1.674I0.0J1.674
N810G00Z0.3
N820X0.152Y0.3
N830G01X-0.4Z-0.3
N840G03X-0.3Y-0.3I0.0J-0.3
N850G02X-1.126Y-1.126I-1.126J0.0
N860X-1.126Y1.126I0.0J1.126
N870X1.126Y1.126I1.126J0.0
N880X1.126Y-1.126I0.0J-1.126
N890G03X0.3Y-0.3I0.3J0.0
N900G00Z0.3
N910X-0.252
N920G01X0.4Z-0.3
N930G03X0.3Y0.3I0.0J0.3
N940X-1.874Y1.874I-1.874J0.0
N950X-1.874Y-1.874I0.0J-1.874
N960X1.874Y-1.874I1.874J0.0
N970X1.874Y1.874I0.0J1.874
N980X-0.3Y0.3I-0.3J0.0
N990G00Z0.3
N1000X-0.248Y0.1
N1010G01Y-0.4Z-0.4
N1020G02X-1.326Y-1.326I-1.326J0.0
N1030X-1.326Y1.326I0.0J1.326
N1040X1.326Y1.326I1.326J0.0
N1050X1.326Y-1.326I0.0J-1.326
N1060G00Z0.4
N1070X0.348Y-0.4
N1080G01Y0.4Z-0.4
N1090G03X-1.674Y1.674I-1.674J0.0
N1100X-1.674Y-1.674I0.0J-1.674
N1110X1.674Y-1.674I1.674J0.0
N1120X1.674Y1.674I0.0J1.674
N1130G00Z0.4
N1140X0.152Y0.3
N1150G01X-0.4Z-0.4
N1160G03X-0.3Y-0.3I0.0J-0.3
N1170G02X-1.126Y-1.126I-1.126J0.0
N1180X-1.126Y1.126I0.0J1.126
N1190X1.126Y1.126I1.126J0.0
N1200X1.126Y-1.126I0.0J-1.126
N1210G03X0.3Y-0.3I0.3J0.0
N1220G00Z0.4
N1230X-0.252
N1240G01X0.4Z-0.4
N1250G03X0.3Y0.3I0.0J0.3
N1260X-1.874Y1.874I-1.874J0.0
N1270X-1.874Y-1.874I0.0J-1.874
N1280X1.874Y-1.874I1.874J0.0
N1290X1.874Y1.874I0.0J1.874
N1300X-0.3Y0.3I-0.3J0.0
N1310G00Z0.4
N1320M30
%

My G code shows

%
O0010
N10 Rapid to: 0 Feed mve to: 7G40G?????????(OFF SCREEN)
N20 Rapid to: 0
N30T00 Program End 6
But the toolpaths and z steps are on the right screen window before I edit.

 ???

Offline Graham Waterworth

*
  • *
  •  1,890 1,890
  • Yorkshire Dales, England
    • View Profile
Re: Simulation
« Reply #1 on: February 04, 2007, 05:45:49 PM »
You need to make sure notepad is set to save in .TXT format and not rich text.

Graham.
Without engineers the world stops
Re: Simulation
« Reply #2 on: February 04, 2007, 07:33:07 PM »
Now using .txt
Making headway