Hello
Guest
it is
March 28, 2024, 11:38:17 AM
Guest
Login
Register
Menu
Home
Help
Search
Calendar
Members
Members
View the memberlist
Search For Members
Login
Register
YouTube
Machsupport Forum
/
Mach Discussion
/
General Mach Discussion
/
Beginner question - Mach Input
« previous
next »
Print
Pages:
1
Go Down
Author
Topic: Beginner question - Mach Input (Read 4015 times)
0 Members and 1 Guest are viewing this topic.
swbre
11
Beginner question - Mach Input
«
on:
October 19, 2011, 09:18:58 PM »
I have installed the demo version of Mach3 on a PC and I have a breakout board connected to the printer port. I want to connect an E-Stop switch as my next step. In section 4.14 of the Mach3 Software Installation and Configuration Manual there is a sample schematic. On the upper right hand of that schematic there is a line "To E-Stop Input". My question is where do I connect that line on the breakout board? Do I use one of the breakout board inputs, pins 10-13 and 15?
Attached is a picture of my breakout board. Thanks to Chuck Hoelzen.
Stephen.
Logged
Hood
25,835
Carnoustie, Scotland
Re: Beginner question - Mach Input
«
Reply #1 on:
October 20, 2011, 02:03:10 AM »
Yes, just choose an input thats not presently being used then set that up as the E-Stop in Ports and Pins, Inputs.
Hood
Logged
Tweakie.CNC
9,196
Super Kitty
Re: Beginner question - Mach Input
«
Reply #2 on:
October 20, 2011, 02:09:47 AM »
Stephen,
Connect the EStop wires, one to GND and the other to any spare input pin (pin 10 would be good). Then configure Mach / Ports and Pins / Input signals / EStop to Port #1, Pin 10.
Tweakie.
Logged
PEACE
swbre
11
Re: Beginner question - Mach Input
«
Reply #3 on:
October 20, 2011, 08:11:22 AM »
It works. I get an external Estop signal. Yeah!
I only used the portion shown in yellow (on the attached) for experiment/trial purposes.
«
Last Edit: October 20, 2011, 08:13:28 AM by swbre
»
Logged
Tweakie.CNC
9,196
Super Kitty
Re: Beginner question - Mach Input
«
Reply #4 on:
October 20, 2011, 08:28:39 AM »
Hi Stephen,
You are going to be an expert in no time
Glad you got it sorted.
Tweakie.
Logged
PEACE
swbre
11
Re: Beginner question - Mach Input
«
Reply #5 on:
October 20, 2011, 09:38:07 AM »
I have no experience with connecting hardware to a PC so this is a good start. Next I'll do some limit switches.
I noticed my Diagnostics screen has more information than what is shown in the manual (Mach3Mill_1.84_UserGuide.pdf) Appendix 1, Screenshot pullout. I have something like Port 1 pin status LED indicators. Has there been a revision to the system that didn't get included in the manual?
Logged
Hood
25,835
Carnoustie, Scotland
Re: Beginner question - Mach Input
«
Reply #6 on:
October 20, 2011, 10:13:27 AM »
Mach is constantly evolving and trying to keep the manual up to date would be a very expensive thing to do, expensive in time for Brian as well as money, so afraid it is what it is.
Hood
Logged
swbre
11
Re: Beginner question - Mach Input
«
Reply #7 on:
October 21, 2011, 11:56:13 AM »
I was wondering if there is any information on the Port 1 Pins current State area? Why 24 Led's? I would expect 25. And why is the 4th LED lit when I have my E-Stop input tied to pin 15 on the breakout board?
Thanks for the replies and help.
Stephen
Logged
Print
Pages:
1
Go Up
« previous
next »