Hello Guest it is December 12, 2024, 11:44:51 AM

Author Topic: Mach3 and Windows 7 64 bit  (Read 13442 times)

0 Members and 1 Guest are viewing this topic.

Offline ALR

*
  •  13 13
Mach3 and Windows 7 64 bit
« on: December 12, 2010, 11:00:34 AM »
Hello.  I have just obtained Mach3 and installed on Windows 7 64 bit system.  In a different post I heard from Klaus that these may not be compatible so I thought I would start a new post.  Is Mach3 compatible with 64 bit systems.  If not can the 64 bit system be modified in some fashion.  I found reference on the PC to a virtual PC system.  Does anyone have experience with this problem.  Currently, I am unable to access the LPT port with Mach 3.  I have performed the Driver test with no outcome.

Any help would be appreciated.

ALR
Re: Mach3 and Windows 7 64 bit
« Reply #1 on: December 12, 2010, 11:35:36 AM »
The PPort diver will not work with 64 bit.
You could use an external motion control since they don't use the pport.

Mike
We never have the time or money to do it right the first time, but we somehow manage to do it twice and then spend the money to get it right.
Re: Mach3 and Windows 7 64 bit
« Reply #2 on: December 12, 2010, 12:08:51 PM »
smooth stepper, it's a usb device that act's like a buffer. They are said to work well

Offline Jeff_Birt

*
  •  1,107 1,107
    • Soigeneris
Re: Mach3 and Windows 7 64 bit
« Reply #3 on: December 13, 2010, 10:03:33 AM »
Mach's parallel port driver will not work on a 64 bit OS. I would suggest looking at the the SmoothStepper: http://www.soigeneris.com/SmoothStepper-details.aspx (my website). The SmoothStepper is a motion control board. It basically acts like the parallel port drive and parallel port of your PC as far as Mach is concerned. Since all the critical pulse generation is done in dedicated hardware most folks see improved, smoother performance of their machines. There are also similar boards such as KFlop, DSPMS, and Galil. Depending on your machine's requirements on of them may be a better fit for you.
Happy machining , Jeff Birt
 

Offline ALR

*
  •  13 13
Re: Mach3 and Windows 7 64 bit
« Reply #4 on: December 14, 2010, 09:12:55 PM »
Thanks for all of the advice.  I have decided that I will swap computers and use the older 32 bit XP machine.  I have already swapped the parallel port and software.  I can use Mach3 to control output on the port pins.  However, I am only measuring 3.35VDC.  Is this enough to drive the breakout board?  If not, what needs to be done to get the voltage up?

Offline Hood

*
  •  25,835 25,835
  • Carnoustie, Scotland
Re: Mach3 and Windows 7 64 bit
« Reply #5 on: December 15, 2010, 02:41:14 AM »
However, I am only measuring 3.35VDC.  Is this enough to drive the breakout board?  If not, what needs to be done to get the voltage up?

It depends on the breakout, some are buffered and happy on 3.3v some are not, have a look at the manufacturers specs as it should tell you.
Hood
Re: Mach3 and Windows 7 64 bit
« Reply #6 on: January 10, 2011, 09:04:10 AM »
sorry guys, i already posted this question somewhere else.

I've just ordered on ebay, for 10 pounds (UK) a PCI parallel port which is guaranteed (by the seller) that will work on XP64.

If that is true, is there any chance that mach3 will run properly?

Thanks

Offline Hood

*
  •  25,835 25,835
  • Carnoustie, Scotland
Re: Mach3 and Windows 7 64 bit
« Reply #7 on: January 10, 2011, 09:10:52 AM »
Answered to your other   post.

Hood