Messages

71

General Mach Discussion / Re: Getting small movements which not supposet to..

« on: June 13, 2013, 10:16:20 AM »

Sorry, is SSR (Solid State Relays) I thought with the new board I would be able to run the AC servo but not.
The board is not the problem, stepper driver wired to this board works, but not the signal out from CN1A(MRJ2S).
Also I get an error from SS when AC servo is powered on and then SS crashed.
Is SS's output signal the same as C10?          

72

General Mach Discussion / Re: Getting small movements which not supposet to..

« on: June 13, 2013, 05:16:17 AM »

This is the new board I made:



and still can not get the AC servo turning, on another Mach3 controller the BOB is a C10 board form CNC4PC and it worked perfectly with SSD (blue squary shape in the middle of the board).

73

General Mach Discussion / Re: Getting small movements which not supposet to..

« on: June 11, 2013, 03:23:59 AM »

Ok, there was a slight problem with my homemade board;


when MRJ2S CN1 connected to this board it does not correspond, but it does on another system, so I'm sure something is not right with the board, will re-build a new board with my Direct PCB printing epson T22:
http://diydrones.com/profiles/blogs/direct-pcb-printer.

Here is the MRJ2S-350A in step/Dir mode:
http://s1204.photobucket.com/user/cncfreakcncfreak/media/BVB25L%20cnc%20conversion/M4V05950_zps587ff3dd.mp4.html

74

General Mach Discussion / Re: Getting small movements which not supposet to..

« on: June 10, 2013, 12:26:22 PM »

I wired the cw & ccw of MRJ2S-350A's CN1A to SS today, it is now in step/dir mode. Will set the Pr tomorrow.

75

General Mach Discussion / Re: Getting small movements which not supposet to..

« on: June 08, 2013, 05:01:50 AM »

What is SS/ESS?, what do they stand for?

Found this:
http://www.machsupport.com/forum/index.php?topic=21036.50;wap2

76

General Mach Discussion / Re: Getting small movements which not supposet to..

« on: June 07, 2013, 03:58:10 AM »

When connecting to BOB CN1A is used, if using varialble speed control mode CN1B is used:

77

General Mach Discussion / Re: Getting small movements which not supposet to..

« on: June 06, 2013, 10:33:02 PM »

This came to my mind, If M03/M04  is called it won't start the spindle Automatically because it is using a Variable speed controller connected to CN1B, If I take the CN1A step and Dir wires to SS port 1 Pin 8 & 9, what else do I need to configure in order to make it spin when M03 command is called?

78

General Mach Discussion / Re: Getting small movements which not supposet to..

« on: June 06, 2013, 04:48:08 AM »

Thanks Hood!!



By the way I swapped the encoder to Shimpo RE2-60-C.



http://www.google.com.tw/imgres?q=shimpo+encoder,+RE2-60&um=1&sa=N&hl=en&tbm=isch&tbnid=cceWuiystzB94M:&imgrefurl=http://www.plazathai.com/show-246265.html&docid=m3UK9OMP2sKpTM&imgurl=http://www.plazathai.com/uppic/59/3ab3798a16927a44a3a5bd1ed334d559.jpg&w=800&h=600&ei=2ESwUfrNMc28kQXW8oH4Ag&zoom=1&ved=1t:3588,r:1,s:0,i:83&iact=rc&dur=488&page=1&tbnh=183&tbnw=231&start=0&ndsp=61&tx=161&ty=73&biw=1920&bih=974

79

General Mach Discussion / Re: Getting small movements which not supposet to..

« on: June 06, 2013, 03:55:54 AM »

Assigning Pins:
A-Port # = 3
A-Pin #= 1

B-port # =3
B-pin # = 2

As for Index....

80

General Mach Discussion / Re: Getting small movements which not supposet to..

« on: June 06, 2013, 02:56:22 AM »

I'm using SS, USB.