Messages

2031

General Mach Discussion / Re: Outputs

« on: October 17, 2016, 03:46:59 AM »

Hi Karl,

I have sent you a PM.

Tweakie.

2032

Promote and discuss your product / Re: Free CNC ART DISK www.cncdxffiles.com

« on: October 17, 2016, 02:41:12 AM »

Excellent work and thanks for sharing.

Tweakie.

2033

General Mach Discussion / Re: Outputs

« on: October 17, 2016, 01:55:59 AM »

If you attach your .xml file I will take a look.

The file is in your Mach3 folder named <your profile>.xml (typically Mach3Mill.xml) copy it then rename it to KarlJuettner.xml then use the reply / Additional Options tabs to attach it to your reply.

Tweakie.

2034

General Mach Discussion / Re: BB card vs motion control card

« on: October 16, 2016, 08:26:59 AM »

If i'm wrong someone will correct me but I'm fairly certain the the parallel port will not handle the encoder signal and pulse rates needed for servos very well. My encoders are 10,000 per rev and motors can do 3000 rpm so it needs a pretty fast connection.

This may be entering into the twilight zone but note to self…
“Tweakie be prepared to be hammered” 

Mach3 is not a closed loop system so does not get to see the higher speed encoder signals that are required by the servo drives to verify that the step direction signals have been performed correctly.

Tweakie.

2035

General Mach Discussion / Re: BB card vs motion control card

« on: October 16, 2016, 06:42:44 AM »

In the end one  can add a parallel card(s) to any computer .

There are many good reasons for using an external motion controller although my personal preference is using the parallel port with Windows XP but
please keep in mind that the parallel port can only be used with 32 bit operating systems running Windows 7 (or earlier) and laptops are not supported.

Tweakie.

2036

General Mach Discussion / Re: Mach3 incorrectly interpreting gcode

« on: October 14, 2016, 10:33:35 AM »

I think you need to go into Config. / General Config. and change the IJ Mode.

If you then Regen. Toolpath the display will be correct and the code should run just fine.

Ideally your Gcode should contain the G90.1 or G91.1 (as appropriate) and this is perhaps a failing of your CamBam post processor.

Tweakie.

2037

Third party software and hardware support forums. / MOVED: XHC New Generation Mach3 Motion Control Card.

« on: October 13, 2016, 03:59:38 AM »

This topic has been moved to Promote and discuss your product.

http://www.machsupport.com/forum/index.php?topic=33420.0

2038

Mach3 under Vista / Re: Problem running programs on Mach3

« on: October 13, 2016, 01:36:53 AM »

Pics and code would be useful.

Tweakie.

2039

General Mach Discussion / Re: New to Mach3 just starting still on Demo, asking question can anyone help.

« on: October 12, 2016, 08:26:15 AM »

But I could do with a radio button to the main screen to turn on Flood cooling and turn it off again the same as M08 and then M09 in a program.

Is there a way of doing this?

Hi Adrian,

Welcome to the forum.

Setup the Flood Mist Control in Config. / Ports & Pins / Spindle Setup. This will let you toggle the Output# you choose for the Flood Ctrl-F (M8/M9) button on the main screen.

It’s a learning experience but using one of the Screen Editor’s will enable more buttons, for example; Mist (M7), to be added to your screen.

Tweakie.

2040

General Mach Discussion / Re: Outputs

« on: October 11, 2016, 08:01:06 AM »

Hi guys, I am new here in this forum. But I'm beginning to feel completely stupid. I configured ports, inputs, outputs and everything as described in various manuals and videos. The problem is that the prgrammed outputs, either by M3, 4 and 5 as well as the ones set by macros are working fine (blinking when activated) on the diagnostic screen while I'm running my G-code. but on no pin on the breakout board is anything happening! What the hell is wrong with it. It's a brans new board, so I doubt that anything is wron with it. THe board is connected via USP port. All inputs when activated by home switches for example are fine. The LED's are switching on and the inputs are visible on the display screen. Any ideas??? Please Help!!! Thanks Karl

I think your best plan would be to contact the manufacturer of your USB board to find out which pin is allocated (or recommended) for the spindle control (M3,4,5). Then make sure that pin (or pins) is / are correctly set-up within your plug-in's software.

Tweakie.