Hello Guest it is December 05, 2021, 07:15:42 PM

Author Topic: Fusion360 post processors - anyone here know about editing ??  (Read 3773 times)

0 Members and 1 Guest are viewing this topic.

Offline dude1

*
  •  1,253 1,253
    • View Profile
Re: Fusion360 post processors - anyone here know about editing ??
« Reply #10 on: October 14, 2016, 03:12:27 AM »
yer there are operations that you perform last in fusion, other things go nanana. there is a new version of the dogbone addon I have not checked it out yet I might do it now

Offline dude1

*
  •  1,253 1,253
    • View Profile
Re: Fusion360 post processors - anyone here know about editing ??
« Reply #11 on: October 14, 2016, 04:32:22 AM »
Dave the new version works better it put's out less junk and is quite fast, I will have a good play with I let you know if it's worth your time

Offline Davek0974

*
  •  2,607 2,607
    • View Profile
Re: Fusion360 post processors - anyone here know about editing ??
« Reply #12 on: October 14, 2016, 05:02:28 AM »
ok thanks, is it just dog-bone or does it do T-bone as well?

Offline dude1

*
  •  1,253 1,253
    • View Profile
Re: Fusion360 post processors - anyone here know about editing ??
« Reply #13 on: October 14, 2016, 06:47:47 AM »
just dogbone

Offline Davek0974

*
  •  2,607 2,607
    • View Profile
Re: Fusion360 post processors - anyone here know about editing ??
« Reply #14 on: October 14, 2016, 06:49:50 AM »
ok thanks

Offline rufan

*
  •  38 38
    • View Profile
Re: Fusion360 post processors - anyone here know about editing ??
« Reply #15 on: November 12, 2020, 03:27:53 PM »
Dear Davek,

I very curious what you changed in the post processor to output a tapping cycle for each hole.
At this moment my output for M84 is like below but it is wrong.

M84 P1.5 Q-21. SS955 RS955
X123.5
X103.5
X83.5
X63.5
Z15.

Can you help me with his?

Offline Davek0974

*
  •  2,607 2,607
    • View Profile
Re: Fusion360 post processors - anyone here know about editing ??
« Reply #16 on: November 12, 2020, 03:48:11 PM »
I'm afraid not much now - been too long and i don't use Fusion any more

This is one of my tapping cycles though...

N80 M5
N82 M9
N84 M1
N86 T97 M6
N88 G54
N90 M7
N94 G0 X-12.7 Y28.725
N96 G43 Z15. H0
N100 Z5.
N104 M84 Q-18.875 P1.25 S350 R350
N106 Z5.
N110 Z15.
N114 G53 G0 Z0.
N116 G90

Dave
Re: Fusion360 post processors - anyone here know about editing ??
« Reply #17 on: November 13, 2020, 04:50:49 AM »
Hi Davek
I'm using Fusion 360, now full version except lots of function :-[ :-[ :-[ :-[ :-\, but ALL project using the A rotary axe can't works! Have You any idea about it? I posted on post processor section but no answer yet!
Tanks

Offline Davek0974

*
  •  2,607 2,607
    • View Profile
Re: Fusion360 post processors - anyone here know about editing ??
« Reply #18 on: November 13, 2020, 06:10:57 AM »
Sorry but no, way beyond me, try doing the Fusion support forum, they are generally very good