Hello Guest it is March 28, 2024, 12:27:48 PM

Author Topic: Mach 111 stops while cnc router is cutting.  (Read 5352 times)

0 Members and 1 Guest are viewing this topic.

Offline Daner

*
  •  32 32
    • View Profile
Mach 111 stops while cnc router is cutting.
« on: September 25, 2019, 10:00:27 AM »
Hi all, hope someone can help me with this issue i have been having

While cutting a sign for example, it will start cutting and working
then it stops , just like if you were to click the stop button on the mach 111 control panel .

The mach11 control panel then becomes unusable.

The only way to get things running again is to shut down the computer and start over, hoping you can find the starting point on the project.
Most of the time the job is scrap.
This all just happens some times ,about 40% of my jobs.

I have checked settings in the windows 7 to make sure the computer does not sleep.
I havent done any updates to Mach 111.

My cnc router needs a parallel port connection on a computer, or I would try another computer.

any idea or tips?

Thanks

Offline Tweakie.CNC

*
  • *
  •  9,196 9,196
  • Super Kitty
    • View Profile
Re: Mach 111 stops while cnc router is cutting.
« Reply #1 on: September 26, 2019, 01:15:38 AM »
Do you have a valid Mach3 license ?  -  if not then Mach3 will only run ~500 lines of Gcode before stopping.
PEACE

Offline Daner

*
  •  32 32
    • View Profile
Re: Mach 111 stops while cnc router is cutting.
« Reply #2 on: September 26, 2019, 09:20:59 AM »
Yes I do have a valid license.

Offline Tweakie.CNC

*
  • *
  •  9,196 9,196
  • Super Kitty
    • View Profile
Re: Mach 111 stops while cnc router is cutting.
« Reply #3 on: September 26, 2019, 09:53:37 AM »
When Mach3 stops, what message do you get in the status box at the bottom of the screen ?
PEACE

Offline Daner

*
  •  32 32
    • View Profile
Re: Mach 111 stops while cnc router is cutting.
« Reply #4 on: September 26, 2019, 10:09:17 AM »
I think I get a message to activate windows.

It’s not hooked up to the internet
Could it be I need to do a mach111 update?

Thanks

Offline ZASto

*
  •  423 423
    • View Profile
Re: Mach 111 stops while cnc router is cutting.
« Reply #5 on: September 26, 2019, 01:52:28 PM »
Welllll... you should activate your windows. Simple s that. You can activate it by phoning MS.
Make no mistake between my personality and my attitude.
My personality is who I am.
My attitude depends on who you are.

Offline Daner

*
  •  32 32
    • View Profile
Re: Mach 111 stops while cnc router is cutting.
« Reply #6 on: September 26, 2019, 03:38:18 PM »
Yes I agree
But this is a older computer
With the parallel port
You would think windows would be activated

Offline Daner

*
  •  32 32
    • View Profile
Re: Mach 111 stops while cnc router is cutting.
« Reply #7 on: October 10, 2019, 05:48:18 PM »
I need some help here,
I took the computer in and they cleaned up a corrupt  hard drive and installed windows.
My problem now is, Its not sending any signal through the parallel port to the cnc machine.
All my connections seem good and I can see the X,Y,Z jogging correctly on the monitor .
Any help where to look next would be greatly appreciated
Thanks
Daner

I checked the pins and ports and they look correct.

Offline ZASto

*
  •  423 423
    • View Profile
Re: Mach 111 stops while cnc router is cutting.
« Reply #8 on: October 10, 2019, 07:29:57 PM »
Did "they" reinstalled Win 7 32-bit or 64-bit?
If "they" installed 64-bit version take your money back.
Mach3 can not communicate with parallel port under 64-bit OSes.

Mine computer is still "old" one with LPT port and running under Win XP :) and is only dedicated to CNC. No internet connection but visible on local LAN.
Have a spare motherboard (Intel mini-ITX desktop board).
Make no mistake between my personality and my attitude.
My personality is who I am.
My attitude depends on who you are.

Offline Daner

*
  •  32 32
    • View Profile
Re: Mach 111 stops while cnc router is cutting.
« Reply #9 on: October 10, 2019, 07:47:10 PM »
they installed windows 7 32 bit …(This was the correct one?)
That's what I requested
Thanks
« Last Edit: October 10, 2019, 07:49:18 PM by Daner »