Hello Guest it is March 28, 2024, 09:33:25 AM

Author Topic: Mach3 and UHU Servo controller  (Read 7997 times)

0 Members and 1 Guest are viewing this topic.

Mach3 and UHU Servo controller
« on: May 04, 2007, 07:45:37 PM »
Hi ALL!
Is it possible to use Mach3 with UHU Servo controller ?  (http://www.uhu-servo.de)

Regards Yuriy
Re: Mach3 and UHU Servo controller
« Reply #1 on: May 04, 2007, 10:29:58 PM »
looking at there doc's they "should" work...
Fixing problems one post at a time ;)

www.newfangledsolutions.com
www.machsupport.com
Re: Mach3 and UHU Servo controller
« Reply #2 on: May 07, 2007, 08:28:31 PM »
Hello Yuriy
Yes it is possible,I have 4 of these ,3 presently running, and 1 for future spindle motor.
I have the 200 volt version on a gutted out anilam system,this has a 110 dc  power  supply
so they work well.

Rick

Offline sebba

*
  •  42 42
    • View Profile
Re: Mach3 and UHU Servo controller
« Reply #3 on: March 08, 2015, 06:46:02 AM »
Hello.... after 8 years... :D

So, better late than never...  I have to work with AC servos for now... :)
In fact, I have some OSAI OSS-200 drivers and S-4030 motors and - like a big (old) boy - I want to play with them :)
But - as you can easily guess - this play should be managed by Mach3

After some research, I found this UHU servocontroller and I'm wondering if I can find someone with more experience with these devices and who can share his's experience and results, pros/cons reasons etc

thanks,
Seb

Offline Hood

*
  •  25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: Mach3 and UHU Servo controller
« Reply #4 on: March 08, 2015, 07:26:46 AM »
Seb,
 the UHU has not really taken off, or at least I never see much mention of it here. How well it works I have no idea but I would have thought if it was a good option then it would be widely used.

Personally I would go down the route of external controller that outputs analogue commands, in fact I have with the CSMIO/IP-A and it works very well.
There are others that people use,
Galil
DSPMC
Kflop with Kanalog.
 I have no experience of them but they are all widely used by people with Mach and you will find support on these forums for all of them.

Hood

Offline sebba

*
  •  42 42
    • View Profile
Re: Mach3 and UHU Servo controller
« Reply #5 on: March 08, 2015, 11:50:37 AM »
Thanks for your input, Hood
I just contacted the guy who sell this device: http://bukovinskygroup.com/catalog/product_info.php?products_id=29
And he told me this device will do the job

I think I'll order one to test it... :)

Regards,
Seb

Offline Hood

*
  •  25,835 25,835
  • Carnoustie, Scotland
    • View Profile
Re: Mach3 and UHU Servo controller
« Reply #6 on: March 08, 2015, 06:13:29 PM »
Post your results please.

Hood

Offline sebba

*
  •  42 42
    • View Profile
Re: Mach3 and UHU Servo controller
« Reply #7 on: March 09, 2015, 01:46:01 PM »
of course! :)

I just placed the order, hope I'll have the parcel with no delay! :)