Hello
Guest
it is
April 18, 2024, 10:34:04 PM
Guest
Login
Register
Menu
Home
Help
Search
Calendar
Members
Members
View the memberlist
Search For Members
Login
Register
YouTube
Machsupport Forum
/
Mach Discussion
/
General Mach Discussion
/
Setup table dimmension with gcode file.
« previous
next »
Print
Pages:
1
2
»
Go Down
Author
Topic: Setup table dimmension with gcode file. (Read 5142 times)
0 Members and 1 Guest are viewing this topic.
jaustin
36
Setup table dimmension with gcode file.
«
on:
December 28, 2013, 04:54:52 PM »
Having a little problem, when i load my gcode into mach 3 looking at the tool display window the part is outside of my table in display window.
I know it has to be something that is not set up correctly with my inputs could someone look at the attached screen shots and see if they can see something that is not correct.
I have my home set up with table to the front and to the right.
push the right arrow and table will move to the left and push the up arrow the table will move to the front.
Logged
Hood
25,835
Carnoustie, Scotland
Re: Setup table dimmension with gcode file.
«
Reply #1 on:
December 28, 2013, 05:07:05 PM »
Just jog to centre of table then zero the X and Y DROs then Regen and see if that helps.
Hood
Logged
Overloaded
4,921
Re: Setup table dimmension with gcode file.
«
Reply #2 on:
December 28, 2013, 05:10:50 PM »
I think your Y Max should be 132 and the Min 0.00 ... Very similar to the X settings.
Logged
jaustin
36
Re: Setup table dimmension with gcode file.
«
Reply #3 on:
December 28, 2013, 05:19:01 PM »
I noticed that 132 and when I changed it to match the x settings. The punisher comes out upside down.
Logged
jaustin
36
Re: Setup table dimmension with gcode file.
«
Reply #4 on:
December 28, 2013, 05:30:42 PM »
corrected home
Logged
Overloaded
4,921
Re: Setup table dimmension with gcode file.
«
Reply #5 on:
December 28, 2013, 05:37:17 PM »
put 132 in the Y Home Off box.
Then you will be setup with 0,0 in the proper direction.
Russ
Logged
jaustin
36
Re: Setup table dimmension with gcode file.
«
Reply #6 on:
December 28, 2013, 05:51:35 PM »
changed to 132 but when i went back into it was changed to 5.19
then the punisher is out side of the box.
when i try to re zero manual by moving the axis I can not go in the direction to bring it within the window.
The y axis hits the front of the mill past the home switch.
Logged
jaustin
36
Re: Setup table dimmension with gcode file.
«
Reply #7 on:
December 28, 2013, 06:16:38 PM »
I moved it the punisher to a different section of cambam and up loaded gcode and it fell right on to the table in the display window
Logged
jaustin
36
Re: Setup table dimmension with gcode file.
«
Reply #8 on:
December 28, 2013, 06:57:59 PM »
Forgot to say thanks for your help OverLoaded.
Thanks
John
Logged
Hood
25,835
Carnoustie, Scotland
Re: Setup table dimmension with gcode file.
«
Reply #9 on:
December 29, 2013, 09:09:48 AM »
Maybe you need to try and get an understanding of work offsets
Hood
Logged
Print
Pages:
1
2
»
Go Up
« previous
next »