Hello Guest it is October 17, 2019, 02:50:09 PM

Author Topic: Constructing a Low Profile Tool Height Setter.  (Read 49250 times)

0 Members and 1 Guest are viewing this topic.

Offline Tweakie.CNC

*
  • *
  •  7,951 7,951
  • Super Kitty
    • View Profile
    • Tweakie.CNC
Re: Constructing a Low Profile Tool Height Setter.
« Reply #70 on: January 01, 2013, 04:57:52 AM »
Hi Guys,

Although it was my original intention to make this an ‘open source’ project for anyone to construct, commercial interest was shown. They took their time deciding but following a reasonable offer I have now sold the design.

Tweakie.
Success consists of going from failure to failure without loss of enthusiasm.  Winston Churchill.

Offline Sam

*
  • *
  •  988 988
    • View Profile
    • hillbillyhilton.com
Re: Constructing a Low Profile Tool Height Setter.
« Reply #71 on: January 01, 2013, 12:11:11 PM »
That's awesome Tweakie!
"CONFIDENCE: it's the feeling you experience before you fully understand the situation."
Re: Constructing a Low Profile Tool Height Setter.
« Reply #72 on: January 12, 2013, 01:03:30 PM »
Hi Guys,

Although it was my original intention to make this an ‘open source’ project for anyone to construct, commercial interest was shown. They took their time deciding but following a reasonable offer I have now sold the design.

Tweakie.


Where can we buy one?
"Gravity, its not just a good idea its the law"
Re: Constructing a Low Profile Tool Height Setter.
« Reply #73 on: February 18, 2013, 04:59:24 PM »
is there an idea when one these would be available to buy?
Frank
Re: Constructing a Low Profile Tool Height Setter.
« Reply #74 on: February 18, 2013, 05:02:14 PM »
I am also very intrested in the plans or to buy a ready built unit.
Re: Constructing a Low Profile Tool Height Setter.
« Reply #75 on: February 22, 2013, 08:36:52 AM »
Can you tell me what transistors you used in your circuit board?
Frank

Offline Tweakie.CNC

*
  • *
  •  7,951 7,951
  • Super Kitty
    • View Profile
    • Tweakie.CNC
Re: Constructing a Low Profile Tool Height Setter.
« Reply #76 on: February 22, 2013, 08:50:45 AM »
Hi Guys,

I am really sorry, but I have agreed not to disclose any further details.  :'(  (This is the problem when an idea is sold but I just could not refuse the cash).

Tweakie.
Success consists of going from failure to failure without loss of enthusiasm.  Winston Churchill.
Re: Constructing a Low Profile Tool Height Setter.
« Reply #77 on: February 22, 2013, 07:06:47 PM »
You can't even tell us where to buy one??? :(
"Gravity, its not just a good idea its the law"
Re: Constructing a Low Profile Tool Height Setter.
« Reply #78 on: November 10, 2015, 01:31:00 PM »
Would this probe work on a es915 spindle head which is ceramic and requires a  ground magnet attached to the tool collet.
Would like to eliminate the ground wire,
Re: Constructing a Low Profile Tool Height Setter.
« Reply #79 on: November 14, 2017, 10:55:51 PM »
Hey Tweakie....I know this is an old post..but I am tired of alligator cliipping the ground to my router bits!!!! Looking to get a switch type to set my Z height...I know you sold your design, where can I get one?

Thanks
Leslie