HiCON Motion Controller

Machsupport Forum
/
Third party software and hardware support forums.
/
HiCON Motion Controller (Moderator: Vital System Support)

HiCon users forum

Pages: « 1 2 3 4 Go Down

		Subject / Started by	Replies / Views	Last post
0 Members and 26 Guests are viewing this board.
		THC hicon integra card problem Started by laurent.milhet	2 Replies 54,873 Views	July 26, 2023, 10:23:31 AM by laurent.milhet
		zero X, Y, Z using a probe Started by abex49	1 Replies 60,312 Views	November 02, 2023, 09:15:14 AM by abex49
		Firmware issue on Hicon integra 7766 Started by Andreas.naesager	2 Replies 122,168 Views	January 22, 2024, 05:43:33 PM by Andreas.naesager
		ANYONE KNOW THE FACTORY IP SETTING ON THE 7766 BLUE BOARD? Started by novation1	1 Replies 109,818 Views	July 30, 2024, 01:01:18 AM by TPS
		Is HICON PWM support not possible? Started by jang	2 Replies 116,096 Views	August 24, 2024, 08:16:34 PM by Vital System Support
		7737 Pin Mapping to Mach4 Started by McRoth	5 Replies 155,137 Views	August 25, 2024, 11:01:07 AM by McRoth
		Spindle Setup with 7866 control and VFD Started by McRoth	2 Replies 117,258 Views	September 08, 2024, 10:43:13 PM by McRoth
		Integra Spindle Orientation? Started by McRoth	0 Replies 97,389 Views	September 10, 2024, 02:46:00 PM by McRoth
		Spindle Orientation Started by Cbyrdtopper	8 Replies 200,024 Views	September 16, 2024, 02:18:26 PM by Cbyrdtopper
		7766 plug in? Started by yelims20	1 Replies 118,373 Views	September 23, 2024, 09:43:42 AM by yelims20
		Encoder Feedback Gain Not Doing Anything, Index Wrong Started by McRoth	3 Replies 120,938 Views	April 13, 2025, 09:03:08 PM by McRoth
		new conversion from mach 3 to mach4 feed rate bouncing Started by fozzyber	0 Replies 4,049 Views	October 29, 2025, 06:41:19 PM by fozzyber
		updated Mach 4 and the Hicon plug in, stuttering, Jerky Started by lgr	1 Replies 12,575 Views	November 11, 2025, 05:08:53 PM by lgr
		Legacy Syil X5 with Hicon 7754 controller Started by peu	3 Replies 9,714 Views	April 11, 2026, 10:06:05 PM by peu
		HiCON Mini 77E4 J6 header wiring examples - request Started by cnc-22	0 Replies 99 Views	June 04, 2026, 05:22:15 PM by cnc-22

Pages: « 1 2 3 4 Go Up

Machsupport Forum
/
Third party software and hardware support forums.
/
HiCON Motion Controller (Moderator: Vital System Support)

Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)

Locked Topic
Sticky Topic
Poll

SMF 2.0.19 | SMF © 2021, Simple Machines
XHTML
RSS
WAP2
Theme Design by Kiseki Studio