Messages

1171

Mach4 General Discussion / Re: Comments about Mach4 in Demo

« on: April 24, 2014, 09:30:29 PM »

Pan the tool path with both mouse buttons.

Other hints:
Left double click orients the path in the top down view.
Right double click orients the path in the ISO view.

Steve

1172

Mach4 General Discussion / Re: Comments about Mach4 in Demo

« on: April 24, 2014, 02:10:17 PM »

LOL!!!  You don't know how many times I have said I would fix that date!!!  I'm going to do it NOW! 

1173

Mach4 General Discussion / Re: Comments about Mach4 in Demo

« on: April 23, 2014, 11:50:23 PM »

Alt-Enter executes the MDI from the keyboard.  Since it is multi-line, alt-UP and alt-down cycle through the previous commands.

Keyboad control is via a plugin that has not been released.  Just mouse around for a bit until we release the keyboard stuff.

Steve

1174

Galil / Re: Old Dynapath System 10 upgrading to Galil CS 18420 ICM 2900 No idea on wiring???

« on: April 18, 2014, 01:25:37 PM »

Hmm...  Are you able to run the Galil with the Terminal.  Meaning do you get encoder counts in the watch window?

You do not have to setup the Mach encoders for the Galil, so that isn't it.  They should be fed to Mach by the plugin.

Steve

1175

Galil / Re: Old Dynapath System 10 upgrading to Galil CS 18420 ICM 2900 No idea on wiring???

« on: April 17, 2014, 06:17:05 PM »

By balance, you mean not drift?  If so, you can use the OF command on the Galil to correct.  And I believe there is a pot on the amp that can adjust that to.  And the point become moot once the servos are energized and the Galil is holding them in position.

Steve

1176

Galil / Re: Limit switch problem

« on: April 17, 2014, 06:12:35 PM »

BTW, there is/was a pretty good explanation of this in a thread on this forum somewhere.  Finding it is the problem.

Steve

1177

Galil / Re: Limit switch problem

« on: April 17, 2014, 06:11:40 PM »

It is not you that is confused!  What you said is correct.  You can test this in the Galil terminal and using the watch window.  If LSCOM is positive, the data record will show one way with a NC switch as opposed to when LSCOM is negative.  I can't remember which way it goes at the moment, so you will just have to test and see.

Look at the limit in the watch window when you have it wired LSCOM to +12v and hook a NC switch up to it.  If limit switch is 1, then CN needs to be configure accordingly.  CN is configured with the limits active low check box in the plugin.  Because when the switch is depressed, the limit switch value in the watch window should go to 0.  And vice verse.  Once this is set so the Galil sees what you want, then you may have to reverse the polarity of the signal for that limit switch in Ports and Pins.  Negate is what it is called, I believe.  At some point, you will get both Mach and the Galil to agree on the switch configuration.

Steve

1178

Galil / Re: Old Dynapath System 10 upgrading to Galil CS 18420 ICM 2900 No idea on wiring???

« on: April 16, 2014, 10:45:04 PM »

http://www.ormec.com/LinkClick.aspx?fileticket=upw7DE2FD8A%3D&tabid=168&mid=757

That is the manual for your drives.  It looks like you may need to wire the limits in parallel with the Galil. 

Steve

1179

Galil / Re: Old Dynapath System 10 upgrading to Galil CS 18420 ICM 2900 No idea on wiring???

« on: April 16, 2014, 08:12:22 PM »

What drives are they?  Model # and make.  There has to be a way around that!  Hard to tell not being able to look at it and all...

Make sure that the motors are "enable" on the ports and pins screen.  No need to set step and dir pins.  Just enable them.

Steve

1180

Galil / Re: Limit switch problem

« on: April 16, 2014, 08:08:23 PM »

LSCOM to -12v.  That will reverse the polarity of the signal.  One wire from RSLX/FLSX to one pole of the NC switch and the other pole to ground. Then play with the active low check box until it works.    That should do it. 

Steve