Hello Guest it is September 20, 2021, 01:32:03 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - MarkC

Pages: « 1 2 3 4 5 6 7 8 9 10 »
71
General Mach Discussion / Re: single block problems
« on: November 21, 2006, 10:22:12 PM »
Duh!
Thats right, I remember you writing that now.
I happened so seldom on my system, probably the last time was 6-8 months ago, I thought it was fixed cuz I updated several times in that timespan.
It's so frustrating because I can't replicate it, it's very random

72
General Mach Discussion / Re: single block problems
« on: November 21, 2006, 09:18:12 PM »
Chaoticone:
what happens with your system?

73
General Mach Discussion / Re: single block problems
« on: November 21, 2006, 09:08:52 PM »
Chaoticone:
the version was the only thing I changed. I agree that is probably a bug
Hood:
Yep tried the XML file. No luck. Coolant on only when system is in RESET. I always make a backup. Oh the NC file is correct, when I edited it to put in the *, I made the two lines into one. I reloaded 1.9.07 and will use that to make parts for the time being. I thought about doing a complete re-install after removing ALL files. I tried an uninstall, but left the folder otherwise intact

74
General Mach Discussion / Re: single block problems
« on: November 21, 2006, 08:16:05 PM »
Went from Mach3 D1.90.070 to V2.0.012, I just mentioned Mach2 cuz I was also having problems then. Only does it once in a while. Like I said I single blocked it twice (with D 1.9) and about 5 or 6 times after and it worked perfectly all other times.. It's frustrating because Brian said this was fixed in V2, and now I'm having more problems than ever

75
General Mach Discussion / Re: single block problems
« on: November 21, 2006, 07:49:30 PM »
 >:(
Tried it with a longer program. It goes to the M30. Yes there is a CR after the M30.
Anyone got any ideas why my coolant doesn't work after updating the version?

76
General Mach Discussion / Re: single block problems
« on: November 20, 2006, 09:37:17 PM »
Yeah, I can single block in now in cycle, but it's useless. It goes to the M30 line and stays there and can't cycle start

77
General Mach Discussion / Re: single block problems
« on: November 20, 2006, 08:18:36 PM »
Mine does the same. I just use cutter comp to adjust size. I have my cam system to default to comp on.

78
General Mach Discussion / Re: single block problems
« on: November 20, 2006, 07:54:07 PM »
I simply cannot put it in single block while in cycle. I get a "No singlestep in G41/G42 program" error. If I hit feed hold, I get the same error if I try then too.
At least before, I could get single block. Occasionally it would take off though, see first post

79
General Mach Discussion / Re: single block problems
« on: November 20, 2006, 07:01:11 PM »
I updated and have a couple of questions.
First my coolant no longer works. The LED comes on but the solenoid won't fire. The only time coolant comes on is if I press RESET. Next, why did it reset my hotkey settings?
Finally I can't press single block when in cycle as I like to when near the end of a cut to check retract etc. Is that the way it should work

 ???
Confused
Mark

80
General Mach Discussion / Re: single block problems
« on: November 19, 2006, 12:02:38 PM »
 :D
Cool! Will update today

Pages: « 1 2 3 4 5 6 7 8 9 10 »