Hello Guest it is November 28, 2021, 03:59:36 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Robhi

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 »
91
General Mach Discussion / Re: Spindle?
« on: July 22, 2009, 06:24:32 PM »
Hi,
Thanks again.
I would like to turn wood, as well as engraving. I love wood too much. I would like to do so.

How could I know that my forth axes works well?
trying to read your answer next week.
best regards..
Robhi

92
General Mach Discussion / Re: Spindle?
« on: July 22, 2009, 03:01:56 PM »
Hello,
thanks for replying,
I guess that all what I need. it is the forth axis that rotate the workpiece, (only for wood). I do not want the spindle any more LOL. So, could I use a stepper motor in order to rotate the workpiece as the one that I see in this video? http://www.youtube.com/watch?v=2KNit__LJE4

hoping it is possible.

Best regards
Robhi

93
General Mach Discussion / Re: Spindle?
« on: July 21, 2009, 05:29:37 PM »
Hello, thanks so much,

I guess you and Hood are right , but how to configure it to to run normally, slow, fast, and change the direction etc.. and if I can engrave ( write) on à piece of wood ? lathe.
Hoping am clear

Best regards
Robhi

94
General Mach Discussion / stepper motor as a Spindle
« on: July 21, 2009, 02:59:44 PM »
Hello,

I have a machine lathe, with two axes, X one and Z one.

Spindle is à stepper motor that works with step and direction. It works well for turning, about 470 RPM. wood turning.
Could use my spindle (stepper motor) for engraving on wood?

Thanks Robhi

95
General Mach Discussion / Re: Mach3 does not go fast
« on: June 30, 2009, 03:31:22 PM »
Hello,
Thanks Hood, as well as all of you

I did as you said, you are right. I did so and everthing is fine...
Changing the feedrate in mastercam, that was the problem.

Thanks again
Robhi

96
General Mach Discussion / Re: Mach3 does not go fast
« on: June 29, 2009, 03:48:29 PM »
Sorry,

 it is better that I attache the file itself

97
General Mach Discussion / Re: Mach3 does not go fast
« on: June 29, 2009, 03:02:15 PM »
Hi,

I use metric system and my faderate is 100% I tried to use more than this but acceleration stays the same.


98
General Mach Discussion / Mach3 does not go fast
« on: June 28, 2009, 04:14:30 PM »
Hi,

I tried the programme called scorpion that is attached with mach3 files, my mill machine 3 axes goes fast, I finish the file within 4 minutes.

But I tried to do very simple programme that was designed by mastercam x design, my mill goes too slowly, it moves nearly 3mm in 10 minutes.

Is there some thing wrong in my programme?
Robhi

99
General Mach Discussion / Re: Gecko 201 Dir pulse and step pluse?
« on: June 12, 2009, 06:00:21 PM »
Hello, I put 2 in both boxes, I guess it is the same as 0 in both of them, nothing change(for me) .

thanks a lot
Robhi

100
General Mach Discussion / Re: Gecko 201 Dir pulse and step pluse?
« on: June 10, 2009, 02:48:14 PM »
Hello,

Thank you so much, I will try to change this WE.
Thanks again
Robhi

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 »