Hello Guest it is March 29, 2024, 07:15:49 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Robhi

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 »
31
General Mach Discussion / Re: Gecko 320x
« on: May 09, 2013, 11:40:16 AM »
OK.. I will try  all what You have said... hoping it will be OK.. Let you know of course.


thanks for all you
Robhi

32
General Mach Discussion / Re: Gecko 320x
« on: May 09, 2013, 02:51:47 AM »
hi,

yes it is, I use us digital, but what kind of resistor should I use? how many K?
thanks
Robhi

33
General Mach Discussion / Re: Gecko 320x
« on: May 09, 2013, 12:36:22 AM »
hello,

yes I have tried to reversing A/B wires but not the motor as red wire of the motor goes to + and black one goes to G, am sure of that.
and the ERR/RES is always connected to ENC+.
I will try to put all the pots on 10 o'clock and let you know...
there is no load on the motor.

thanks a lot

Robhi

34
General Mach Discussion / Re: Gecko 320x
« on: May 08, 2013, 05:11:10 PM »
hi,
If you are talking about the limit trimpot, I have adjusted it as the P I D, at 11 o'clock, I tried at 10 o'clock but it is the same, always red fault red.
what do you mean by bass-ackwards? and how I could do the same as you?

thanks for your reply
Robhi

35
General Mach Discussion / Gecko 320x
« on: May 08, 2013, 04:03:24 PM »
Hello every body,

I countered a problem as most of people on the web. I have wired my gecko 320x ( I guess correctly) as it mentioned in documents.
trimpot on 11 o'clock,  I have done all the steps and every thing was going fine, testing the encoder, is OK too, sending pulses is fine too, till I have wired the servo motor,

kl 34 180 72. the fault led remains red. I have a power supply of 72 volt, ( bought a kit ) with the encoders etc...so normally everything is compatible.

any help would be appreciated.

thanks in advance
Thanks Robhi

36
I have just replied and everything is ok... you are right Hood port work bad on that PC

thanks again

Robhi

37
Hello

I just have changed the PC, and everything working well, so the port on that PC does not work.

So thanks for all of you for your help, Hood Ian as well as all other members.

just one question please , on this PC when I run driver test, it is written too fast, then excellent.. does that make a problem in the future, tuning motor etc...?

thanks again
Robhi

38
hello,

only Estop, limit and home swiches are mointed.
when the test is ok, I will mount the reste, drives and motors. but till now it doen not work as it is recommended in BOB breakout documents.

normally, when I touch any limit, the led that correspond should come on in the diag page,. only leds on the bob itself that work well.

i do not why.

thanks Hood
Robhi

39
Hi

first for Hood,

I have BOB breakpout board, sound logic, 1.9, servo motors, gecko drives for servo motor, 320x, but till now they are not mounted. Just I would like to test the BOB, ( I have 2 of them, old one which works well before, new one, Both of them do not work)

For Ian,

Normally as you know of course, when we touch any limit or home switch, the yellow led on the diag page should come on,
my home and limit do not come home, whether they are configured active or high.
the Estop too, does not work, if you push it nothing happened, as the limit and home, normallay mach3 must stop when we push Estop, Mine works with or without, does not work with or without Estop.

hoping that I am a little bit clear than before.

Thanks for both of you, and the other members too.
Robhi

40
Hi,

Here is my file.

i have tried to change the address as you have told me, but nothing new. there is nothing on diag page.
It is always as the attached file.
thanks

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 »