Messages

131

General Mach Discussion / power supply

« on: July 10, 2008, 03:41:45 AM »

Hello,

I would like to know if I could use a power supply of 24 volt,  15 ampère for XS-3525/8S-4 of XYLOTEX.. I do not know whether it is dangers or not..

thanks in advance for your help

Robhi

132

General Mach Discussion / Re: Help about "24VDC/5.0A "

« on: December 20, 2007, 02:55:01 PM »

hi,
thankx  for replies, they are great and useful.
thankx again
robhi

133

General Mach Discussion / Re: Help about "24VDC/5.0A "

« on: December 16, 2007, 06:01:15 AM »

Hi, thanks for your replies.
the motor that i have are the followings:

220Ncm - 10mm Shaft - Hybrid Stepper Motor 

Arc Code   AC571157525M
Type   Hybrid Stepper
Holding Torque   220Ncm
Step Angle   1.8°
Rated Voltage   7.5V
Rated Current   2.5A/Phase
No. of Wires   8
Size   57x57x115mm
Shaft Dia.   10mm
Shaft Length (Front)   30mm
Shaft Length (Rear)   30mm
Net Weight   1.74kg

I would like to run the three of them at once ( as am not too clever to run only 2), they would be wired in bipolar parallel,
so as you said I might have a PS of 24VDC/7.25 Am or more.
Am I right?

Robhi

134

General Mach Discussion / Help about "24VDC/5.0A "

« on: December 15, 2007, 06:55:19 AM »

hello,

Could I use a PS that is used for a printer for my:--

The XS-3525/8S-4 Stepper Motor Driver Board
The Perfect Choice For Your Sherline or Taig Four Axis CNC Retrofit

Four axis bipolar drive
±2.5 Amp/Phase PWM controlled drives
up to 35 Volt (w/BEMF)
FULL, HALF, QUARTER, & EIGHTH step/Full Step .

The PS that I would like to use is input 220 volte, output is 24VDC/5.0A .

I do not know if that would work.

any help of you will be appreciated.
thanks

Robhi

135

General Mach Discussion / Re: help with "This is then Winding One"

« on: December 13, 2007, 10:55:54 AM »

hello,
I do Appreciate that, thank you so much.

Robhi

136

General Mach Discussion / help with "This is then Winding One"

« on: December 13, 2007, 10:40:27 AM »

Hi, could you help me to understand what these code mean please?

For BIPOLAR PARALLEL:
Join RED to BLUE
Join YELLOW to BLACK. This is then Winding One.
Join WHITE to BROWN
Join PURPLE to GREEN. This is then Winding Two

does it mean the following or not?

Join RED to BLUE for A
Join YELLOW to BLACK. This is then Winding One. for A#
Join WHITE to BROWN for B
Join PURPLE to GREEN. This is then Winding Two for B#

thanks for your help

137

General Mach Discussion / About Nema motors or other type

« on: December 06, 2007, 08:12:49 AM »

hello,

I do not know if i can ask some information here or not, at any rate am sorry if I can not.

what I like to know, Please, that I have the following drive:-


The XS-3525/8S-4 Stepper Motor Driver Board (Ver 4.00) $175.00

The Perfect Choice For Your Sherline or Taig Four Axis CNC Retrofit

Four axis bipolar drive
±2.5 Amp/Phase PWM controlled drives
up to 35 Volt (w/BEMF)
FULL, HALF, QUARTER, & EIGHTH step/Full Step
Built-in DC-DC Converter for 5 Volt Logic
Filtered and Buffered STEP & DIR Signals
Built-in Break-out:Screw Terminals for Unused Parallel Port I/O
Synchronous Rectification
Internal UVLO and Thermal Shutdown circuitry
Easy connect for most popular Step/Direction control software
Small Size: 5.65" X 2.85"
I would like to to have this type of motors. is it OK? Could they be used with such type of drive? Or I will have prob with?
thanks in advace for your answers

 220Ncm - 10mm Shaft - Hybrid Stepper Motor

 
SPECIAL OFFER at only £22.95!!!!
Normally £39.50

VAT Included, P&P £3.95

Arc Code AC571157525M
Type Hybrid Stepper
Holding Torque 220Ncm
Step Angle 1.8°
Rated Voltage 7.5V
Rated Current 2.5A/Phase
No. of Wires 8
Size 57x57x115mm
Shaft Dia. 10mm
Shaft Length (Front) 30mm
Shaft Length (Rear) 30mm
Net Weight 1.74kg

Robhi
 

138

General Mach Discussion / could I use more than 500 lines ?

« on: November 25, 2007, 10:17:26 AM »

hello,
as u see i am a new settler here, i wanna use mach3 , the prob that i have is that i can not use more than 500 lines in one programme..
is there any solution?
thank in advance